Replacing rear wheel bearing. how to remove?
Remove the rear wheel, then the bearing cap. Then remove the split pin out, the crowed washer and bearing nut & washer. Now remove the outer tapered bearing, and the brake disk ...
SOURCE: Rear Wheel Bearing Repair; 2005 pontiac aztek
Remove the brake caliper
Remove the disc, (rotor)
Remove the 34mm nut on the axel shaft
Remove the three (3) bolts from the back side
You will need a wheel puller (three jaw will work well)
Place the puller over the hub and tighten, this will push the shaft out of the hub. Now you have to pull the hub assy. out of the mounting bracket. I found hitting each side,of the hub with a lead hammer to work well. Don't forget to disconnect the ABS senser on the back side of the hub assy.
Do not over tighten the 34mm axel nut when you install the new assy. If you use an impact whrench on it you will damage the bearing.
SOURCE: remove and replace rear wheel bearing on 1997 f150
REMOVE DIFF COVER ON 3rd MEMBER THERE WILL BE A SMALL 8mm BOLT REMOVE BOLT SLID PIN OUT PUSH AXLE IN AND REMOVE HORSE CLIP DO SAME FOR OTHER SIDE PUSH AXLE IN REMOVE CLIP. YOU'LL NEED A BEARING PULLER TO REMOVE BEARING INSTALL NEW BEARINGS WITH NEW SEAL, INSTALL BOTH AXLE WITH HORSE CLIPS INSTALL PIN AND 8mm BOLT, COVER AND REFILL.
SOURCE: How Do i remove Rear wheel bearing 2005 dodge caravan
raise van take off wheel you must use jackstands or support your van securly its going to rock alot Take off the four bolts located on the back side of the bearing then take out the small bolt from the speed sensor also located in behind the bearing remove the speed sensor. you will need a large mechanics hammer or heavy blunt object. beat the bearing from the back side dont worry about the cog attached you new bearing has one. dont listen to your hanyes or chiltons manuals thanks.
SOURCE: Procedure for replacing rear wheel bearings 2000 Forester
i'm assuming you don't have a hubshark,this is a tool that will alllow you to remove the bearing while the knuckle is attached to the car,you may be able to rent this tool at a auto prts store .if not you need to remove the entie knuckle,first remove the trailing arm bolt,then the lateral link bolt{long and stubborn bolt},disassemble the brake shoes and parking brake cable,abs sensor if equipped the knuckle to strut bolt{no marking necessary they are not eccentric} then you need a to use or borrow a press to remove hub and bearings good luck
SOURCE: how do i replace the rear wheel bearing on my peugeot 206
wheel off remove the tin cap in the centure of the hub undo the big nut put the wheel back on with just 2 bolts finger tight so you can pull the hub off.once the hub is off take the 2 wheel bolts back out.now look in side the hub were the big nut was and you will see a sir clip take that out.then use a socket and a bench vice to press the old bearing out.use the socket and bench vice to put the new bearing back in.
Rear hub and bearing
Click to Enlarge
To install:
Rear hub and bearing
Click to Enlarge
Rear hub removal
Inner wheel bearing removal-rear hub/bearing
Rear wheel bearing removal-2wd
Rear wheel bearing removal-4wd
To install:
Install or connect the following:
Rear wheel bearing installation
hope this helps if so send testimonial comment or even any other questions you have
CAUTION: Turning the differential case (4204) or an axle shaft (4234) with the differential pinion shaft (4211) removed will cause the differential pinion gears (4215) to fall out of the assembly and damage the components. CAUTION: Do not damage the rubber O-ring in the U-washer groove. CAUTION: Do not damage the wheel bearing oil seal (1177). CAUTION: Never remove the wheel bearing oil seal (1177) by itself. Always remove the rear wheel bearing (1225) and the inner wheel bearing oil seal at the same time. 
Installation 
1,543 views
Usually answered in minutes!
×