Location of Charcol Canister and EVAP Emission control solenood valve in hyundai elentra 2002.

on top of the canister purge can , next to the solenoid of same purpose

ossible causes
- Faulty Evaporative Emission (EVAP) Purge Solenoid Control
- Evaporative Emission (EVAP) Purge Solenoid Control harness is open or shorted
- Evaporative Emission (EVAP) Purge Solenoid Control circuit poor electrical connection
What does this mean?
When is the code detected?
An improper voltage signal is sent to Engine Control Module (ECM) through the valve.
Possible symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
P0443 Description
The Evaporative Emission System (EVAP) canister purge volume control solenoid valve uses a ON/OFF duty to control the flow rate of fuel vapor from the EVAP canister. The EVAP canister purge volume control solenoid valve is moved by ON/OFF pulses from the Engine Control Module (ECM). The longer the ON pulse, the greater the amount of fuel vapor that will flow through the valve.

Error Code: P0440
Fault Location:
Evaporative Emission (EVAP) System - Malfunction
Possible Cause:
Malfunction Indicator Lamp (MIL) active.
Soution:
Check Evaporative Emission (EVAP) System Sealing.
Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve .

Error Code: P0441
Fault Location:
Evaporative Emission (EVAP) System - Incorrect Flow Detected
Possible Solutions:
Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
Perform Output Test.
Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve .
Check Evaporative Emission (EVAP) Canister.
Perform Basic Setting.
Check Pipes between Tank Breathing and Throttle Body.

Error Code: P0446
Fault Location:
Evaporative Emission (EVAP) System, Vent Control - Circuit Malfunction
Possible Cause:
Wiring harness.
Evaporative emission (EVAP) canister purge valve.
Engine control module (ECM).

DTC P1446 EVAP CANISTER VENT CONTROL VALVE
The EVAP canister vent control valve is located on the EVAP canister and is used to seal the canister vent.
This solenoid valve responds to signals from the ECM. When the ECM sends an ON signal, the coil in the solenoid valve is energized. A plunger will then move to seal the canister vent. The ability to seal the vent is necessary for the on board diagnosis of other evaporative emission control system components.

This solenoid valve is used only for diagnosis, and usually remains opened. When the vent is closed, under normal purge conditions, the evaporative emission control system is depressurized and allows "EVAP Control System (Small Leak, Gross Leak, Very Small Leak)" diagnosis.

Contact us on the code link if you need additional details.

Hope this helps. Your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

DTC P1446 EVAP CANISTER VENT CONTROL VALVE
The EVAP canister vent control valve is located on the EVAP canister and is used to seal the canister vent.
This solenoid valve responds to signals from the ECM. When the ECM sends an ON signal, the coil in the solenoid valve is energized. A plunger will then move to seal the canister vent. The ability to seal the vent is necessary for the on board diagnosis of other evaporative emission control system components.

This solenoid valve is used only for diagnosis, and usually remains opened. When the vent is closed, under normal purge conditions, the evaporative emission control system is depressurized and allows "EVAP Control System (Small Leak, Gross Leak, Very Small Leak)" diagnosis.

Contact us on the code link if you need additional details.

Hope this helps. Your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

Trouble code P0441 indicates EVAP emiddion control system incorrect purge flow.
Possible faulty purge valve or circuit.
Possible causes: purge line plugged, vacuum hose failure, EVAP purge solenoid failure and/or emission canister clogged.

The coolant sensor is a 2 wire sensor located in the thermostat housing.

Which code specifically? Do not assume you need a new solenoid. Our recommendation will depend on the specific code and some troubleshooting results. I usually recommend checking over all the EVAP vacuum lines and the gas cap too whenever there is a purge valve code. Check the vacuum lines at the cannister in the left rear bumper. I will paste info on the purge solenoid below.

P0440 Evaporative emission (EVAP) system - malfunction

Possible causes: Hose connection(s), intake leak, EVAP canister purge valve

P0441 Evaporative emission (EVAP) system - incorrect flow detected

Possible causes: Hose connection(s), intake leak, EVAP canister purge valve

P0442 Evaporative emission (EVAP) system - small leak detected

Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve

P0443 Evaporative emission (EVAP) canister purge valve - circuit malfunction

Possible causes: Wiring, EVAP canister purge valve, ECM

P0444 Evaporative emission (EVAP) canister purge valve -open circuit

Possible causes: Wiring open circuit, EVAP canister purge valve, ECM

P0445 Evaporative emission (EVAP) canister purge valve -short circuit

Possible causes: Wiring short circuit, EVAP canister purge valve, ECM

P0450 Evaporative emission (EVAP) pressure sensor - circuit malfunction

Possible causes: Wiring, EVAP pressure sensor, ECM

P0455 Evaporative emission (EVAP) system - large leak detected

Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve

P0456 Evaporative emission system - very small leak detected

Possible causes: Mechanical fault, hose connection(s), EVAP pressure "sensor

P0457 Evaporative emission system - leak detected (fuel cap loose/off)

Possible causes: Mechanical fault, hose connection(s), EVAP pressure sensor

P0458 Evaporative emission system, purge control valve -circuit low

Possible causes: Wiring short to earth, EVAP valve

P0459 Evaporative emission system, purge control valve -circuit high
Possible causes: Wiring short to positive, EVAP valve

Evaporative Emission Purge Solenoid

Description & Operation
The duty cycle EVAP canister purge solenoid (DCP) regulates the rate of vapor flow from the EVAP canister to the intake manifold. The Powertrain Control Module (PCM) operates the solenoid.
During the cold start warm-up period and the hot start time delay, the PCM does not energize the solenoid. When de-energized, no vapors are purged. The PCM de-energizes the solenoid during open loop operation.
The engine enters closed loop operation after it reaches a specified temperature and the time delay ends. During closed loop operation, the PCM cycles (energizes and de-energizes) the solenoid 5 or 10 times per second, depending upon operating conditions. The PCM varies the vapor flow rate by changing solenoid pulse width. Pulse width is the amount of time that the solenoid is energized. The PCM adjusts solenoid pulse width based on engine operating condition.
Removal & Installation
The duty cycle evaporative (EVAP) canister purge solenoid is located in the engine compartment near the brake master cylinder.

1. Disconnect electrical connector at solenoid.
2. Disconnect vacuum lines at solenoid.
3. Lift solenoid slot from mounting bracket for Removal & Installation.

To Install:

1. Position solenoid slot to mounting bracket.
2. Connect vacuum lines to solenoid. Be sure vacuum lines are firmly connected and not leaking or damaged. If leaking, a Diagnostic Trouble Code (DTC) may be set with certain emission packages.
3. Connect electrical connector to solenoid.
   

Purge solenoid location:


EVAP cannister location:

CODE PO455 EVAPORATIVE EMISSION SYSTEM LARGE LEAK DETECTED.POSSIBLE CAUSES CANISTER VENT SOLENOID MAY BE STUCK IN OPEN POSITION / EVAP CANISTER TUBE EVAP CANISTER PURGE OUTLET TUBE OR EVAP RETURN TUBE DISCONNECTED OR CRACKED OR CANISTER IS DAMAGED / EVAP CANISTER PURGE VALVE STUCK CLOSED OR CANISTER DAMAGED / FUEL FILLER CAP MISSING LOOSE NOT TIGHT OR THE WRONG PART / FUEL VAPOR HOSES TUBES BLOCKED OR RESTRICED OR FUEL VAPOR CONTROL VALVE TUBE OR FUEL VAPOR VENT VALVE ASSEMBLY BLOCKED /FUEL TANK PRESSURE SENSOR HAS FAILED MECHANICAL FAULT /FUEL TANK CONTROL VALVE IS CONTAMINATED DAMAGED OR HAS FAILED.

Error Code: P0441
Fault Location:
Evaporative Emission (EVAP) System - Incorrect Flow Detected
Possible Cause:
Malfunction Indicator Lamp (MIL) active.
Evaporative Emission (EVAP) Canister Purge Regulator Valve faulty/jammed.
Evaporative Emission (EVAP) Canister Purge Solenoid Valve faulty/jammed.
Evaporative Emission (EVAP) Canister Sealing faulty.
Pipes between Tank Breathing and Throttle Body leaky/blocked.
Hose connection(s).
Intake leak.
Possible Solutions:
Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
Perform Output Test.
Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve.
Check Evaporative Emission (EVAP) Canister.
Perform Basic Setting.
Check Pipes between Tank Breathing and Throttle Body.
VSV connector near air filter box disconnected.

P0441 : Evap. Emission System Incorrect Purge Flow

General Description
The evaporative emission control system prevents hydrocarbon (HC) vapors from the fuel tank from escaping into the atmosphere where they could form photochemical smog. Gasoline vapors are collected in the charcoal canister. The ECM controls the Purge Control Solenoid Valve (PCSV) to purge any collected vapors from the canister back to the engine for combustlon. This valve is actuated by the purge control signal from the PCM and controls fuel vapor from the canister to the intake manifold.
Possible Cause : ● Leakage on hose to PCSV ● Defective PCSV