2002 Jaguar XType Sun-roof one-touch operations reset

Temporary Fix: unsnap off the access door in the overhead ceiling liner behind the sunroof opening;
Use a 4mm hexagon Allen wrench to wind it closed.

The roof slides along a channel actuated by a coiled cord.

Both of the cords pass along a gear attached to the Sunroof motor which pulles the cord tooth by tooth.

There are two plastic wedges that drop into the plastic slides on the sunroof (the plastic slides are behind the more forward metal slides.)

The plastic slides control the tilt of the roof when moved independantly. The plastic wedges join them.

If the roof moves too far back, it is possible for the wedges to stick up and jam the roof open.

This should never happen, but could if the two micro switches on the sunroof motor assy fail to provide feedback to the controller indicating the roofs position.

Access to the Sunroof motor requires you to drop the headliner.

To drop the headliner, the plastic pillar shrouds need to be removed front and back, the seatbelt bolts in the middle secion need to be removed, the oh-**** handle, the front visors, and cabin lights.

3 bolts hold the motor up.

With the motor down you can try* to manually actuate the cords using a flat screwdriver, but move the left and right side evenly a tooth at a time.

Of course of the plastic wedges are jammed, it's not going to budge.

Hope the info is helpful. good luck!

Section 01-17: Roof Panel, Sliding—Electric 1996 Taurus, Sable Workshop Manual DESCRIPTION AND OPERATION Electric Operation The sliding roof panel (502B98):

• is available as an option.
• is electrically operated through the accessory delay relay (controlled by generic electronic module (GEM)).
• is of self-storing design.
• requires a specific headliner.
• utilizes a unique roof console and dome lamp.
• has an air deflector.

The electrical system operates in the following manner:

• Two switches control movement of the roof panel.
• When the SLIDE roof sliding panel switch (15B691) is rocked rearward, the roof sliding outer glass panel (502A82) slides into the storage space between the roof trim panel (51968) and the roof panel, exposing an opening over the front seats.
• When the SLIDE roof sliding panel switch is rocked forward with the roof sliding outer glass panel fully back in the storage space, the roof sliding outer glass panel moves forward from the storage position.
• The rear portion of the roof sliding outer glass panel moves upward on two lifter arms near the end of the forward travel, allowing a weather-tight seal when the roof sliding outer glass panel is closed.
• An AUTO feature allows the SLIDE roof sliding panel switch to be touched momentarily to cause the roof panel to automatically move to the fully open position.
• When the TILT roof sliding panel switch is rocked forward with the roof sliding outer glass panel fully forward, the rear of the roof sliding outer glass panel pops up to the VENT position.
• With the roof sliding outer glass panel in the VENT position, rocking the TILT roof sliding panel switch rearward closes the roof sliding outer glass panel.

--------------------------------------

• Sliding Roof Panel Does Not Open or Close

• Open power feed fuse.
• Circuitry open/shorted.
• Damaged roof sliding panel switch.
• Damaged sliding roof panel motor.

VISUAL INSPECTION CHART Mechanical Electrical

• Damaged roof panel
• Obstructed roof panel
• Guide
• Damaged drive cable(s)

• Open Power Distribution Box Fuses 1 (40A) or 4 (30A)
• Circuitry open/shorted
• Damaged roof sliding panel switch
• Damaged sliding roof panel motor

title says X5, but description says X3. i'll explain for an X5, but X3 with the pano should be the same. and i'll explain function of the roof, not reprogramming.

button is located on the panel at the top near the front & center windshield. its the switch on the far left on this panel. its a switch that not only toggles, but also slides forward & back.

with your finger in front of the button, slide it back & release. this will make the cover slide back and store revealing the sun roof. you know have 2 options (tilt the sunroof up or open the roof completely).

to tilt it up, press up on the rear of the button and release. the rear of both roofs will pop up. to close, push up and release the front of the button or slide the switch forward.

to slide it open completely, repeat what you did to open the protective cover (slide the switch from front to back). the roof will open completely and stow out of the way. to close, slide the switch forward and release. pano roof will now close.

to close the cover, slide the switch forward again.

neat trick: if you want to tilt the sunroof open without opening the protective cover, press up on the rear of the button (when the cover is closed) and release. the cover will separate in the middle exposing about a 2-3 inch mesh, then tilts the sunroof open. to close, push the button forward again.

also, if you are above a certain speed (can't remember what it is off hand) with the sunroof open or tilted, it will close automatically, then perform the neat trick on its own to keep air coming in.

one last trick: if you want to open the windows and sunroof from outside, press & hold the unlock button (forward button on the key) and you will see the windows go down, then the roof will open to vent. releasing the button will stop the motion of the windows & roof.

hope this answered what you were asking.

tilt the sunroof into vent position as far as possible then press and hold the same switch for 30 seconds until you see it move release the switch and immediately press and hold it again the sunroof will close and open fully then close again do not release the button until it reaches the closed position for the second time.

source: owners manual