Secret windshield tip! See clearer and make wipers last much longer!

This type of problem needs to be approached with diligent process of elimination to properly diagnose.
Check for vacuum leaks...with the engine running, spray carb cleaner at each joint and seal along the intake system and intake plenum. If there is a leak the engine idle will change as the spray is taken in through the leak.
The idle air control valve could be faulty or dirty. Remove the idle air control valve and clean the interior with carb cleaner.
There could be deposits in the thottle body causing the throttle valve to stick open. Check for free operation of the throttle valve. Clean the throttley body with throttle body safe (NOT car cleaner) cleaner by removing the intake hose, spraying the cleaner on the paper towel and cleaning the interior of the throttle body while holding the throttle butterfly plate open.
Make sure the throttle cable moves freely and that the return spring is present and working properly.
To go beyond this may require special diagnostic tools.

check the water pump placed under the water bottle or switch the car on dont start it run the water if you dont hear the sound of water pump running its either the pump damaged or something to do with the fuse or wiring

is it a fixed glass or a moveable glass.

Fixed glass is placed against a bead of urethane sealer, like caulking.

Window, Liftgate, Stationary Removal
WARNING: SAFETY GLASSES AND GLOVES MUST BE WORN.
CAUTION: Use only urethane for after-seal to service air and water leaks in urethane seal. Failure to do this may result in additional leaks.
CAUTION: Allow all glass parts installed with urethane ample time to cure. If ample time is not allowed, glass may come loose and/or leak.

1. Remove window wiper pivot arm (17526) .

1. Remove all window glass stops.

1. Using Rotunda Glass Adhesive Cutter 118-00050 or Rotunda Deluxe Glass Adhesive Cutter 163-00001 or equivalent, follow manufacturer's instructions and cut seal and dam around entire outer edge of windshield glass (03100) .

1. Remove glass from vehicle.

1. Trim urethane left on flange with a utility knife or razor blade until surface is smooth and free of cuts. It is not necessary to remove all urethane from the flange if it is cured. However, at no point should existing urethane material exceed 2.54mm (0.10 inch). NOTE: If urethane has not cured completely, remove all uncured urethane using care not to smear urethane on component parts.
   Check flange sealing area for damaged sheet metal or foreign objects which may have caused, or may cause, glass breakage. Service sheet metal if necessary.
   

Installation

1. If existing urethane on metal flange has become contaminated, cut away contaminated urethane with a utility knife or razor blade.

1. If painted sheet metal has been exposed anywhere along the flange, apply Urethane Metal Primer WSB-M2G234-C or equivalent over the painted surface using a clean brush. NOTE: A minimum of 30 minutes is required for primer surface to dry.
   

1. Place the windshield glass on a low, stable work surface, inside up. NOTE: Wipe off immediately after application because it flash-dries.
   

1. Using a lint-free cloth, wipe outer 25mm (1 inch) of inside glass periphery with Urethane Glass Wipe WSB-M5B280-C2 or equivalent.

1. Position mouldings on glass. CAUTION: Allow all glass parts installed with urethane ample time to cure. If ample time is not allowed, glass may come loose and/or leak.
   

1. Thoroughly shake and stir Urethane Glass Primer WSB-M2G314-B or equivalent to ensure uniform pigment mixing.

1. Using a clean brush, apply primer around entire periphery of glass on inside surface as shown. (Allow at least five minutes drying time.)

1. Properly align glass to body.
   1. Make sure lower windshield glass stops are in place at bottom of windshield glass opening.
   1. Place windshield glass into opening. Center it top and bottom, side to side, with about equal clearance around opening.
   1. Using masking tape or crayon, make alignment marks at points on both the windshield glass and the window opening.

1. Remove windshield glass from vehicle and place back on work table.

1. Apply an even bead of Urethane Adhesive WSB-M2G316-B on top of existing urethane around entire window opening using an air pressure cartridge gun. Air line pressure should be around 276 kPa (40 psi). The bead should be large enough to seal the windshield glass but not cause expulsion into vehicle.

1. Install windshield glass onto vehicle, taking care to align marks on glass to those on body. This must be done within 10 minutes of applying urethane.
   
   
   

Windshield seal may be leaking. Find leak repair with clear silicon caulk may work.

You have an oil leak somewhere. If the engine is dirty, one morning, drive to the nearest carwash, turn off motor, and use the pressure washer on the engine compartment. If it is really nasty, buy a cheap can of oven cleaner, (ammonia) and spray it on the engine before using the pressure washer on it. (DONT spray the coil packs, or spark plugs if possible) Then take it for a drive, and look for where the oil is coming out. Probobally an intake gasket. ALWAYS keep your engine compartment spotless! It makes it easy to repair, and troubleshoot. I am up to three people here locally who thought I was full of it, let their engine get nasty, and their cars burned to the ground. Also, when I worked as a service tech, I charged extra, (a LOT extra) if I had to get dirty while fixing a car. I also charged $20 for every time someone called to check on their car prematurely.