20 Most Recent
2005 Toyota 4Runner SR5 V8 Questions & Answers
Where do I check or add transmissionfluid on my 2005 toyota 4 runner sr5 v8
There are two plugs on the drain pan. One drains it, the other is the overflow tube. Take the overflow tube plug out (usually the one in the middle of the pan) and pump Toyota Transmission fluid in, the extra will drain back out.
Don't use the wrong fluid, do it with it warmed up, and if it only has one plug in the transmission pan I was wrong and don't drain it by pulling the only plug out.
All 4 windows won't work and rear door latch won't open! So, I have two problems: Firstly my rear hatch won't open as of yesterday (Keyless entry pushed & it doesn't even make a n
Look at your maintenance manual. To find where your fuse box is located(may be under the hood or under the steering wheel). When you find the fuse box look on the back of the panel flap and you'll find a fuse map. Locate the fuse that corresponds with your problem. It could be the same fuse but not likely. If fuse is blown then replace it with a spare. Most manufacturers will put spare fuses in the box or you could pull a fuse from some where else just to try and see if the problem is still there( make sure it's the same size and understand that it could blow this fuse as well then you will need 2 fuses). Most of the time fuses don't just blow. For some reason it pulled to much load. Probably a dead short in the wiring. I hope this helps.
Toyota code p1750
Code P1750 on your Toyota denotes a problem in the Hydraulic Control System of A/T Clutch Pressure Control Solenoid due to a brake ECU malfunction. The signal is sent to the ECCM by the brake actuator assembly, aka skid control ECU for three seconds to display the code.
Toyota Camry 1991 Auto seat belt not working
Fortunately for you, there are a few ways how to get a seat belt buckle unstuck. To begin with, a seat belt can be stuck due to two reasons: a) the problem may lie in the retractor being locked, and b) dirt or grime may have accumulated on the seat belt, causing it to retract slower than usual and not all the way.
2007 Toyota Camry Le 2.4l. how do i put the ignition coil connetor wires back into the correct position? can you send me a wiring digram with color code?
I can guide you on how to reconnect the ignition coil connector wires correctly on your 2007 Toyota Camry LE 2.4L. Each wire should be connected to the corresponding terminal on the ignition coil.
Here is a general guideline based on the standard wire color-coding for most vehicles:
1. Start by identifying the ignition coil and the connector wires that you need to reconnect.
2. Check the wires for any color-coding. Typically, the wires are color-coded as follows:
- Black or Black with a White stripe
- Yellow or Yellow with a Blue stripe
- Blue or Blue with a Yellow stripe
- Green or Green with a White stripe
Here is a potential wiring configuration (please verify with your vehicle manual or a professional):
- Black or Black with a White stripe wire connects to the negative terminal (-) on the ignition coil.
- Yellow or Yellow with a Blue stripe wire connects to the positive terminal (+) on the ignition coil.
- Blue or Blue with a Yellow stripe wire connects to another terminal on the ignition coil.
- Green or Green with a White stripe wire connects to a different terminal on the ignition coil.
If your wires have a different color scheme, consult a repair manual for your specific vehicle or reach out to a professional for assistance. When reconnecting the wires, ensure they are securely attached to the respective terminals to prevent any loose connections or electrical issues.
I think this helpful
Can I change the tire width size on the same rims?
It is not unsafe to fit wider tyres as long as they are the same type on the same axle.
Many 'boy racers' fit wider tyres thinking it will give more grip.
I would take it to a garage and have the correct size tyres fitted as this will increase the accuracy of the speedometer as well, (due to the circumference being wrong).
Toyota Corolla 1.3 Esteem 2014 model: electronic speedo meter not working,
Info below was taken from the tech service information to diagnose a malfunctioning speedometer. The process has many steps and may not be something you'd want to try to diagnose and repair yourself.
If you have a scan tool that can read ABS codes, you can possibly get some info on what's causing the problem.
The combination meter assembly receives vehicle speed signals from the brake actuator assembly (skid control ECU) via the CAN communication system. The speed sensor detects the wheel speed and sends the appropriate signals to the brake actuator assembly (skid control ECU). The brake actuator assembly (skid control ECU) supplies power to the vehicle speed sensor. The brake actuator assembly (skid control ECU) detects vehicle speed signals based on pulses of the voltage.
If the vehicle speed sensor circuit has a malfunction, the brake actuator assembly (skid control ECU) stores DTCs. Troubleshoot the vehicle stability control system or anti-lock brake system.
Not finding what you are looking for?