I just purchased a 2002 Tacoma Prerunner. The radio antenna (non powered) is broken off at the base. There is what I think is a chrome nut with 4 groves, inside this nut is what remains of the base in which the antenna screws into. It appears that somebody attempted to remove this piece without success, the threads appear to be messed up. How do I get this inner piece out to replace and install a new antenna?
Thanks,
Phil
Use an antenna wrench to remove the chrome nut (I found a wrench on JC Whitney's website). Once the nut's removed, do the following (copied from the factory service manual):
REMOVE ANTENNA ROD
(a) Turn the ignition switch to ”LOCK” position.
(b) Press the ”AM, FM” buttons on the radio receiver, and simultaneously
turn the ignition switch to ”ACC” position.
HINT:
The rod will extend fully and be released form the motor
antenna.
After removing the antenna rod, leave the ignition switch
on ”ACC” position.
NOTICE:
To prevent body damage when the antenna rod is released,
hold the rod while it comes out.
2. Auto Antenna Models:
INSTALL ANTENNA ROD
(a) Insert the cable of the rod until it reaches the bottom.
HINT:
When inserting the cable, the teeth on the cable must face
toward the rear of the vehicle.
Insert the antenna approx. 300 mm (11.8 in.).
(b) Wind the cable to retract the rod by turning the ignition
switch to ”LOCK” position.
HINT:
If the ignition switch is already in ”LOCK” position, do step
1 (c) first, then turn the ignition switch to ”ACC” position.
In case the cable is not wound, twist it, as shown in the
illustration.
Even if the rod has not retracted fully, install the antenna
nut and inspect the antenna rod operation. It will finally retract
fully.
(c) Inspect the antenna rod operation by pressing the radio
wave band select buttons.
You can buy a new power mast online (ex. Discount Toyota Parts) for about $30.
Posted on Apr 04, 2009
need diagram for tacoma v6 firing order
Front 1 3 5
of
vehicle 2 4 6
You have a distributorless ignition. This is the firing order, 1-2-3-4-5-6.
Please remember to rate this answer.
Posted on Feb 12, 2009
firing order for 4.o 05 tacoma and cylynder lay out
here is the best picture I can find.
Posted on Apr 10, 2009
tacoma fuse box diagram
need plug wire firing diagram
For the 2002 Toyota Tacoma:
I do not know if you have the 2.4L, 2.7L or the 3.4L; however I have included all three below.
For the 2.4L AND 2.7L:
Firing Order:
1-3-4-2
Cylinders:
(back)
...4
...3
...2
...1
(front)
Ignition Connections:
(back)
___
o <----4
o <----3
___
o <---2
o <---1
(front)
For the 3.4L:
Firing Order:
1-2-3-4-5-6
Cylinders:
....(back)
5.............6
3.............4
1.............2
....(front)
Let me know if this helped, or if you have an additional information or questions. Feel Free to contact me at FixYa.com!
Posted on Mar 24, 2010
how to wire trailer lights to a toyota tacoma pickup
The easiest way is to get the kit that plugs into the taillight harness to adapt your plug. If one isn't easily available then you can use scotch locks to splice into your trucks harness. Use a test light to make sure you locate the right wires in your trucks harness and go by the wire diagram on the instructions from the plug to hook it up.
I hope this helps!
Posted on Jul 22, 2010
Where is the cabin air filter for toyota tacoma 2003
Hi, their is no cabin filter on your toyota they didnt start fitting cabin filters on these until 2006,.
on the 2006 model the cabin filter is located behind the glove box but if yours is a 2003 then it wont have a cabin filter.
plz rate this solution as i have a whole page of unrated posts, thanks
Posted on Aug 30, 2010
i have error codes of p1300,p1305, p1310, p1315, on my toyota an am looking for the deffinations and issues thse codes create. I have a 2002 tacoma.
P1300 = ignition system malfunction (#1 coil/igniter circuit fault)
P1305 = same as above but #2 coil
P1310 = #3 coil
P1315 = #4 coil
Posted on Dec 19, 2010
me puedes proporcinar la posicion de la cadena de tiempo para una tacoma 4 cilindros motor 2.7 3RZ
Revice los siguientes diagramas para 2002 Toyota Truck Tacoma 2.7L EFI DOHC 4cyl (click over pic for zoom)...
Fig. Timing chains and related components-2.4L and 2.7L (3RZ-FE/M) engines
Fig. Check that the No.1 cylinder is at TDC and the weights of the
No.1 and No.2 balance shafts are at the bottom-2.4L and 2.7L (3RZ-FE/M)
engines
Fig. Crankshaft position sensor rotor location-2.4L and 2.7L (3RZ-FE/M) engines
Fig. No.1 timing chain and camshaft timing sprocket identification and alignment-2.4L and 2.7L (3RZ-FE/M) engines
Espero que le sea de ayuda (recuerde valorar esta respuesta).
Posted on Jan 20, 2011
I need the wiring order on the coils for the 1998 toyota tacoma 4 cylinder
firing order is 1/3/4/2
Posted on Dec 08, 2012
649 questions posted
Usually answered in minutes!
352 Questions
307 Questions
295 Questions
304 Questions
277 Questions