1995 Toyota Camry - Answered Questions & Fixed issues

the thermostat is located driver's side of the vehicle. Follow the upper radiator hose to its end to a water outlet housing. the thermostat is in the outlet. take off the air flter lid and hose and it is easier to get to. take the hose off and the metal line to the housing. the other part of the housing is holding the thermostat. it is held with two 10 mm bolts. good luck.

here is a link for parts, replace both of them same ageand wear on both of them. copy and paste https://www.carparts.com/axle-assembly/toyota/camry/1995 ..

There is a key in sensor, as well as a headlamp-on sensor that both can trigger the warning beep tied to DOOR AJAR. You can disconnect both systems one at a time to find out which oine is causing the warning.

Help in the link https://www.google.com/search?q=1995+toyota+camry+starts+and+dies ..

I have attached to where you align the notch for the cam gear. The harmonic balancer has a notch on it, which you align to the "0" on the lower cover. The belt has alignment marks on them normally crank gear is the dotted line and the cam will be the solid line. Don't reuse an old timing belt of you removed it without marking it first. You should have aligned the gears to there timing spots prior to removing the belt Be very careful if you have to rotate the cam or crank the Pistons can touch the valves and cause damage. Hope this helps.

Question edited into written English with punctuation and stuff :>D Question moved to model category. How on earth does a hood fly off? They have a lock and a safety catch! After the rain, 'Water Displacement Formula 40' spray (WD40) would probably have fixed it, but you compounded the troubles by removing the battery. Now you have to reset the alarm and engine immobilizer. The battery also needs a good 12.8 to 13.2 volts, so it probably needs charging on a battery charger after all the attempts to start it. https://www.google.com/search?q=1995+toyota+camry+le+reset+security ..

check fuel system.

https://youtu.be/1ZRjcJOSFW0. Here's your answer it was driving me crazy and I found this

where can i locate FUSE BLOCK (J/B)?? ' B15 Sentra Forum

www.b15sentra.net > ... > Technical Discussion

Jun. 11, 2007 - 1 - 12 of 12 Posts ... the inside fuse box and the J/B fuse block are the same thing. ... No kidding and a blown fuse is an indication that there is something ... Home · About Us · Terms of Use · Privacy Policy · Help · Contact us.

Accessing the FUSE BLOCK - JUNCTION BOX (J/B) NO.1 ...

forums.nicoclub.com > ... > Q45 Forum / Cima Forum

Mar. 24, 2008 - Accessing the FUSE BLOCK - JUNCTION BOX (J/B) NO.1 ... Hello gents, I need to change a fuse in my 2002 Q45. It's in the #1 Junction Box on the ...

Complain to Toyota, they are fixing some of these car for free. Here is the explanation and the list of problem vehicles.

Oil sludge or black sludge is a solid or gel in motor oil caused by the oil gelling or solidifying, usually at temperatures lower than 100 degrees Celsius. Sludge can be a major contributor to Internal combustion engine problems, and can require the engine to be replaced, if the damage is severe. Sludge is usually caused by the presence of water in the oil, and can accumulate with use. Ways to minimize sludge production and accumulation includes performing frequent oil changes, using synthetic oil, and following the manufacturer's engine maintenance routine.
The following engines were reported by the Center for Auto Safety and/or their manufacturers to have a problem with sludge accumulation:

1996-2001 Toyota 3.0 L 1MZ V6

• August 1996-July 2001 Toyota Camry
• June 1998-May 2001 Toyota Camry Solara
• July 1997-May 2001 Toyota Sienna
• July 1996-May 2001 Toyota Avalon
• November 2000-July 2001 Toyota Highlander
• August 1998-July 2001 Lexus ES300
• January 1998-July 2001 Lexus RX300

1996-2001 Toyota 5SFE I4

• August 1996-July 2001 Toyota Camry
• June 1998-May 2001 Toyota Camry Solara
• August 1996-April 1999 Toyota Celica

try google. we dont stock manuals here

1 2 3 4 5 6 as shown in the images https://www.google.com/search?q=1995+toyota+camry+le+v6+firing+order ..

check they relay under hood and fuse

Scan the PCM for codes. It doesnt sound like a coil problem

check the ecm fuse

1995 Camry 2.2L OBD1 Code 12Trouble Code 12Trouble Code 12 Definition:Engine speed (RPM) sensor -circuitTrouble Code 12 Meaning:Wiring, RPM sensor, ECMDiagnoses Time:Voltage reading between Engine Control Module(ECM) and RPM sensor.http://www.troublecodes.net/toyota/toyota-camry-cressida/

The crankshaft position sensor is located to the right of the water pump Ddirection for removal:

1. Disconnect the negative battery cable.
2. Remove the right hand engine under cover.
3. Remove the right side fender apron seal.
4. Remove the sensor wiring retaining nuts.
5. Remove the bolt and disconnect the crankshaft position sensor wiring, then withdraw the sensor.

To install:

1. Install the sensor and secure with the bolt to 69 inch lbs. (8 Nm).
2. Attach the engine wiring.
3. Install the right hand fender apron seal.
4. Install the right hand engine under cover.
5. Connect the negative battery cable.
6. Reset any electrical components such as the radio or clock.

The best solution yo u'll get from books at www.reliable-store.com These are books containing info on repair, service, troubleshooting, parts info, assembling dissemble, removal, error/fault codes, wiring diagrams and everything on any vehicles cars, atv, trucks. forklifts, boats, excavators etc.

This type of problem needs to be approached with diligent process of elimination to properly diagnose. Check for vacuum leaks...with the engine running, spray carb cleaner at each joint and seal along the intake system and intake plenum. If there is a leak the engine idle will change as the spray is taken in through the leak. The idle air control valve could be faulty or dirty. Remove the idle air control valve and clean the interior with carb cleaner. There could be deposits in the thottle body causing the throttle valve to stick open. Check for free operation of the throttle valve. Clean the throttley body with throttle body safe (NOT car cleaner) cleaner by removing the intake hose, spraying the cleaner on the paper towel and cleaning the interior of the throttle body while holding the throttle butterfly plate open. Make sure the throttle cable moves freely and that the return spring is present and working properly. To go beyond this may require special diagnostic tools.

At this website www.reliable-store.com I found all complete guide, much better language, complete detail in 800+ pages, and they also have live assistance feature