Top 10 1996 Toyota Camry Questions & Answers

1996 Toyota Camry Logo

Question

  • 6,106 People Helped

where can i find a vacuum hose diagram for 1996

where can i find a vacuum hose diagram for 1996 camry 2.2

Posted by on

Answer

  • Most Helpful of 1 Answers

hi,
i have provided the vacuum hose diagrams for Toyota Camry model.Can you please tell us the reasons for you searching the diagram?.We are ready and happy to help you!. Please rate my solution as helpful.2a4b72e.gif104d8cb.jpg

Posted on Feb 27, 2010

Question

  • 5,262 People Helped

how to replace EGR valve in 1996 toyota camry

how to replace EGR valve in 1996 toyota camry

Posted by on

Answer

  • Most Helpful of 2 Answers

It is simple. It looks like a little flying saucer or pancake and it is in the rear of the engine on top near windshield.There are two hoses that plug into it from the exhaust, and one coming out, and one on bottom (total of 4). You can just unplug the hoses and replace them easily.

Posted on Dec 18, 2009

Question

  • 4,936 People Helped

where is the power window relay switch located?

where is the power window relay switch located? Windows and door locks stopped working.

Posted by on

Answer

  • Most Helpful of 1 Answers

This may be the location: There is a power main relay, it's located on the rear of the junction block in the left side of the dash behind the cover, on the front are the fuses and on the rear is the relay, it's the one closest to the center of the car, there are two other relays, these are identical so you could swap one of them and see if that fixes the problem.
If that doesn't do it, one cheap way to find this info is a Chilton manual at the library.

Posted on Mar 16, 2011

Question

  • 4,900 People Helped

How do you align or focus headlights beams that are to

How do you align or focus headlight beams that are to low or to high?

Posted by on

Answer

  • Most Helpful of 1 Answers

AIMING THE HEADLIGHTS

The headlights must be properly aimed to provide the best, safest road illumination. The lights should be checked for proper aim and adjusted as necessary. Certain state and local authorities have requirements for headlight aiming; these should be checked before adjustment is made.

CAUTION About once a year, when the headlights are replaced or any time front end work is performed on your vehicle, the headlight should be accurately aimed by a reputable repair shop using the proper equipment. Headlights not properly aimed can make it virtually impossible to see and may blind other drivers on the road, possibly causing an accident. Note that the following procedure is a temporary fix, until you can take your vehicle to a repair shop for a proper adjustment.
Headlight adjustment may be temporarily made using a wall, as described below, or on the rear of another vehicle. When adjusted, the lights should not glare in oncoming car or truck windshields, nor should they illuminate the passenger compartment of vehicles driving in front of you. These adjustments are rough and should always be fine-tuned by a repair shop which is equipped with headlight aiming tools. Improper adjustments may be both dangerous and illegal.
For most of the vehicles covered by this guide, horizontal and vertical aiming of each sealed beam unit is provided by two adjusting screws which move the retaining ring and adjusting plate against the tension of a coil spring. There is no adjustment for focus; this is done during headlight manufacturing.
Because the composite headlight assembly is bolted into position, no adjustment should be necessary or possible. Some applications, however, may be bolted to an adjuster plate or may be retained by adjusting screws. If so, follow this procedure when adjusting the lights, BUT always have the adjustment checked by a reputable shop.
Before removing the headlight bulb or disturbing the headlamp in any way, note the current settings in order to ease headlight adjustment upon reassembly. If the high or low beam setting of the old lamp still works, this can be done using the wall of a garage or a building:

  1. Park the vehicle on a level surface, with the fuel tank about 1 / 2 full and with the vehicle empty of all extra cargo (unless normally carried). The vehicle should be facing a wall which is no less than 6 feet (1.8m) high and 12 feet (3.7m) wide. The front of the vehicle should be about 25 feet from the wall.

fbcb5a7.jpg

Fig. : Location of the aiming screws on most vehicles with sealed beam headlights


97dee4f.jpg

Fig. : Dual headlight adjustment screw locations-one side shown here (other side should be mirror image)

9a545e8.jpg

Fig. : Example of headlight adjustment screw location for composite headlamps
  1. If aiming is to be performed outdoors, it is advisable to wait until dusk in order to properly see the headlight beams on the wall. If done in a garage, darken the area around the wall as much as possible by closing shades or hanging cloth over the windows.
  2. Turn the headlights ON and mark the wall at the center of each light's low beam, then switch on the brights and mark the center of each light's high beam. A short length of masking tape which is visible from the front of the vehicle may be used. Although marking all four positions is advisable, marking one position from each light should be sufficient.

031bc2f.jpg

Fig. : Low-beam headlight pattern alignment

758eed8.jpg

Fig. : High-beam headlight pattern alignment

  1. If neither beam on one side is working, and if another like-sized vehicle is available, park the second one in the exact spot where the vehicle was and mark the beams using the same-side light. Then switch the vehicles so the one to be aimed is back in the original spot. It must be parked no closer to or farther away from the wall than the second vehicle.
  2. Perform any necessary repairs, but make sure the vehicle is not moved, or is returned to the exact spot from which the lights were marked. Turn the headlights ON and adjust the beams to match the marks on the wall.
  3. Have the headlight adjustment checked as soon as possible by a reputable repair shop.

Hope helped with this information. Good luck (remember rated this help).

Posted on Nov 10, 2009

Question

  • 4,789 People Helped

HOW TO SET TIMING ON 96 TOYOTA CAMRY 2200 MOTOR

HOW TO SET TIMING ON 96 TOYOTA CAMRY 2200 MOTOR SIZE

Posted by on

Answer

  • Most Helpful of 2 Answers

Click on the following free direct Link. It has the Timing: Pulley, Belt and Mark Diagrams for your 1996 Toyota Camry. Plus additional Instructional and Directional Diagrams.

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/1996/make/toyota/model/camry/1996_toyota_camry_timing_belt_diagram_marks.htm

Posted on Mar 28, 2010

Question

  • 4,394 People Helped

locating the fuel pump relay on 1996 toyota camry

locating the fuel pump relay on 1996 toyota camry

Posted by on

Answer

  • Most Helpful of 2 Answers

Only the 1MZ V6 has this relay. On the 4-cyl, the fuel pump runs off the circuit opening relay, which is in relay block 6, behind the instrument cluster.

Posted on Jan 21, 2012

Question

  • 4,383 People Helped

1996 toyota camry manual

anybody who has 1996 toyota camry manual...could you plz post a copy..thank you

Posted by on

Answer

  • Most Helpful of 3 Answers

fan motor in my camry that runs the heater and AC. just quit

Posted on Sep 01, 2010

Question

  • 4,270 People Helped

Toyota Camry 96. Won't start the engine turns over

Toyota Camry 96. Won't start the engine turns over but doesn't start. The alternator and starter are working fine the coil sparks there are new spark plugs and the ignition module tested fine so I'm at a lost for ideas now. The car is getting fuel and there's a new fuel pump. The filter is clean and everything seems to check out. Can you help???

Posted by on

Answer

  • Most Helpful of 3 Answers

Ignition timing could be off, the plug wires and firing order may be scrambled, there could be a large air leak into the intake manifold, the EGR could be stuck open, the fuel pressure is too high and flooding the engine through the cold start injector, the MAP or MAF sensor is faulty, very dirty fuel injectors, idle air control valve defective, the engine coolant temp sensor is faulty (stuck at full hot).

Posted on Feb 10, 2011

Question

  • 4,000 People Helped

1997 toyota camry engine diagram exploded view

1997 toyota camry engine diagram exploded view

Posted by on

Answer

  • Most Helpful of 1 Answers

This might assist, it is for the V6. The 4-cyl diagram is eg1.pdf

http://www.turboninjas.com/camry/eg2.pdf

Posted on Dec 18, 2011

Question

  • 3,772 People Helped

radio wire diagram for 1996 toyota camry

radio wire diagram for 1996 toyota camry

Posted by on

Answer

  • Most Helpful of 1 Answers

Larger harness:
Green: front right speaker (+)
Pink: front left speaker (+)
Grey: +12V only when ignition switch is at ON or ACC
Blue with yellow stripe: +12V, always on
Blue: front right speaker (-)
Violet: front left speaker (-)
Brown: ground

Smaller harness: Red: rear right speaker (+)
Black: rear left speaker (+)
White: rear right speaker (-)
Yellow: rear left speaker (-)

Posted on Feb 25, 2010

1,692 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

1995 Toyota Camry
1995 Toyota Camry

1,794 Questions

1994 Toyota Camry
1994 Toyota Camry

1,723 Questions

1998 Toyota Camry
1998 Toyota Camry

1,526 Questions

2002 Toyota Camry
2002 Toyota Camry

1,268 Questions

1997 Toyota Camry
1997 Toyota Camry

1,099 Questions

Top Toyota Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

1996 Toyota Camry Camry

  • 1996 Toyota Camry Camry

Most Popular Question

took care check engine light now no

  • Cars & Trucks
Loading...