2003 Mitsubishi Montero Sport - Answered Questions & Fixed issues


Hi try this disconnecting battery for half hour

2003 Mitsubishi... | Answered on Jan 18, 2018 | 318 views


Hello Tarochan,

The first place to start is to retrieve any fault codes the on-board computer may have registered.

The flashing lamp you are seeing is alerting you to a possible problem with the braking system or a possible fault is occurring withing the IPS (Instrument Panel Cluster) itself.

So..the best advise I can give you is to have a mechanic do a scan check for fault codes. This may provide some idea as where to start looking for possible problems.

2003 Mitsubishi... | Answered on Aug 31, 2017 | 103 views


I said i need an airg cause my boyfriend keep one texting me brus

2003 Mitsubishi... | Answered on Jun 23, 2017 | 528 views


yes heater core hoses
inlet manifold to internal heater radiator

a related answer from fixya 2010
http://www.fixya.com/cars/t5391988-best_way

look for this part as well
leaking 0 rings or corroded metal cooling pipes in the engine bay

26309677-eqpognyxwb4jkumc2nrzorbv-5-0.jpg

2003 Mitsubishi... | Answered on Oct 13, 2016 | 121 views


If it is leaking coolant out of the weep hole it is bad, if the bearings are noisy it is bad, if the shaft and pulley wobble it is bad.

2003 Mitsubishi... | Answered on Oct 12, 2016 | 76 views


There isn't a reset for this. It shut down because it got too hot. Serious damage can happen from over heating. Like a seized crankshaft. I would check to see if it can be turned by hand first. If you can't turn it, it is dead.

2003 Mitsubishi... | Answered on Mar 27, 2016 | 56 views


RUN A JUMPER FROM THE BATTERY TO THE STARTER TERMINAL. THIS WILL REVEAL IF THE WIRING IS BAD.

2003 Mitsubishi... | Answered on Jun 16, 2015 | 30 views


Did you install the belt with the number one piston on the compression stroke and have the distributor pointed at the number 1 plug connector wire. If so, you must of missed the belt placement by one tooth. If everything was correct like you mentioned it should of started. So, you made a small mistake that you will have to check again where, Im sorry :.(

Number 1 piston on the TDC of it's compression stroke, distributor pointed at the number 1 plug wire.
When on the compression stroke, the valve rockers on that piston will be relaxed (sealed) and the rockers will have play in them at that setting. Both rockers, intake and exhaust on number 1 will be loose when on the compression stroke of that piston.

2003 Mitsubishi... | Answered on Jun 12, 2015 | 152 views


Use a relay, no matter how you hook it up. Remember that anytime you install accessories into a vehicle. RELAYS RELAYS RELAYS

2003 Mitsubishi... | Answered on Jun 12, 2015 | 85 views


lift hood and open the fluid container that says windshield fluid only.

2003 Mitsubishi... | Answered on Jun 12, 2015 | 63 views


Be sure you did blow a head gasket!!. Check for antifreeze loss, or white milky stuff in the oil. Look under the oil fill cap and radiator cap for white greyish goo. That will be a blown gasket from over heating.

To reset the engine light, there should be a toggle switch located somewhere under the dash, just switch it to the other side and your done. it is a very tiny switch, so you may need to look pretty hard for it.

2003 Mitsubishi... | Answered on Jun 12, 2015 | 171 views


Might try resetting the system by disconnecting the battery lead for a few minutes. The system may be confused with the disconnection and new install, so removing power may reset it. Also, there is a engine light reset switch under the dash. Not exactly sure right where it is, but it is just a simple switch that can be moved from one side to the other. Like a toggle switch, but smaller. This resets the engine light headache and starts a new counter for the next time it lights up for something. Mitsubishi placed these switches on all there vehicles. My 86 truck has it right behind the speedometer under the dash. I use to have to switch it every 50K miles because it was programmed to turn on in that time range. I finally got tired of it and removed the bulb from the engine light warning thing. I don't suggest you remove the bulb,, but I do suggest you look under the dash for that reset switch and flick it to the other side for normal reset procedure.

2003 Mitsubishi... | Answered on Jun 12, 2015 | 410 views


You will have to get under the vehicle and find the oil pan directly under the engine. On the oil pan you will locate the bolt to drain the oil pan. They usually are at the lowest point on the oil pan so that all the oil is drained from the pan when removed.

2003 Mitsubishi... | Answered on Jun 12, 2015 | 225 views


in short your only options are a locksmith but the back window out and replace it later or let it run out of gas still in the morning call the dealership getting the VIN number of the vehicle and they can tell you the keyless entry cocode however I don't think that I help you because Fabian your battery will be dead because if I would have ran outta gas in the ignition switch would have been on all night and the battery will be dead in the morning

If you need further help, reach me via phone at https://www.6ya.com/expert/james_9c1b039055413ffa

2003 Mitsubishi... | Answered on Mar 06, 2015 | 62 views


Your going to need a wiring diagram. You have a MAF,MAP, IAT and EGR sensor problem. My guess would be a signal wire or ground is bad. These four sensors are right at the throttle body. The mass air flow sensor and the manifold absolute pressure sensor are one in the same. The intake air sensor is next to it. All are located in the air induction plenum. Between the throttle body and the air filter. The Engine gas recirculation valve/sensor is right behind the throttle body. So check the harness from the air filter/ MAF to the engine harness plug. Look for conduit that is rotted away and/or melted.

2003 Mitsubishi... | Answered on Feb 25, 2015 | 286 views


You know you can take it to a dealer or local shop

So your question is can you replace them

Maybe if you can find something on You Tube Video
to get an idea what is involved

If you want to change colors,forget that

Some of the switches may have to be replaced to
replace a burnt lamp & the colors will be what you get
when the vehicle was built as new

Need to provide the complete story when you come here

All we can do is guess & point you in some direction

2003 Mitsubishi... | Answered on Nov 25, 2014 | 84 views

Not finding what you are looking for?
Cars & Trucks Logo

339 questions posted

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

Marvin
Marvin

Level 3 Expert

85111 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...