20 Most Recent 1999 Lincoln Navigator Questions & Answers


What do you mean by "hot wired"?

1999 Lincoln... | Answered on Mar 16, 2019


Bad coil will produce a check eng code . If it said po4003 it will 3 coil that is bad if it saids po4001 it is coil pack 1 and so on it will show a code on a misfire with a bad coil. Most like no 1 cylinder coil was bad you kept driving and damaged the cat

1999 Lincoln... | Answered on Mar 03, 2019


Heidi if you take your Lincoln to Auto Zone they do not charge for checking out service engine soon codes.

1999 Lincoln... | Answered on Sep 29, 2018


Odometer The instrument cluster receives odometer rolling count status from the PCM-engine computer and stores the mileage in non-volatile memory (NVM). When the instrument cluster fails to receive the odometer rolling count status for more than two seconds, the odometer display will show dashes.

HEC Dealer Test Mode
To enter the HEC Dealer Test Mode, depress and hold the instrument cluster SELECT/RESET button and then turn the ignition switch to the RUN position. Continue pressing the SELECT/RESET button (5 seconds) until tESt is displayed in the odometer. The SELECT/RESET button must be released within 3 seconds of the odometer displaying tESt to begin the dealer test mode. Depress the SELECT/RESET button to advance through the following steps until dtc is displayed. Depressing the SELECT/RESET button will display any continuous DTCs stored before proceeding to the next step.

All segments illuminated Illuminates all odometer segments. If any odometer segment is inoperative, INSTALL a new instrument cluster; REFER to Instrument Cluster .
Odometer Display Description GAGE Activates gauge sweep of all gauges, then displays present gauge values. Also carries out the checksum tests on ROM and EE. If the gauge sweep is inoperative, INSTALL a new instrument cluster; REFER to Instrument Cluster . All segments illuminated Illuminates all odometer segments. If any odometer segment is inoperative, INSTALL a new instrument cluster; REFER to Instrument Cluster . bulb Illuminates all micro-controlled lamps and LEDs (low oil pressure/high coolant temperature, low fuel, service engine soon, brake, low range). INSTALL a new bulb or LED as necessary. r Returns to normal operation of all micro-controlled lamps and LEDs and displays hexadecimal value for ROM level (used when requesting assistance from the hotline). If alternating flashes of FAIL and ROM level are displayed, INSTALL a new instrument cluster; refer to Instrument Cluster . EE Displays hexadecimal value for EE level (used when requesting assistance from the hotline). If alternating flashes of FAIL and EE level are displayed, INSTALL a new instrument cluster; refer to Instrument Cluster . dt Displays hexadecimal coding of final manufacturing test date (used when requesting assistance from the hotline). dtc Displays continuous DTCs. Pressing the SELECT/RESET button will display any DTCs stored before proceeding to the next step. enG Displays the English speed in mph. Speedometer will indicate present speed within tolerances. Display will show 0 if input is not received, if input received is invalid for one second or more, or if speed is 0. m Displays the English speed data (mph) received from the PCM via SCP Network. Displays the metric speed in kph. Speedometer will indicate present speed within tolerances. Display will show 0 if input is not received, if input received is invalid for one second or more, or if speed is 0. tAc Displays the tachometer data received from the PCM via the SCP Network. Tachometer will indicate present speed within tolerances. Display will show 0 if input is not received, if input received is invalid for one second or more, or if engine rpm is 0. FUEL Displays the actual A/D fuel level. The fuel gauge will display a filtered fuel level value. This filter will keep the pointer from moving suddenly or erratically. If the value displayed is between 0 and 20, the circuit is shorted. GO to Pinpoint Test D .
  • 255=open send +/-0
  • 232=Full stop +/-10
  • 215=Full mark +/-10
  • 178=3/4 mark +/-8
  • 138=1/2 mark +/-7
  • 93=1/4 mark +/-5
  • 41=E mark +/-4
  • 54="LOW FUEL" (0-59)
  • 0-18=short (0-20 max.)
OIL Displays the code (0-255) for the oil pressure switch input to the HEC. Displays the oil pressure reading input to the HEC. Oil pressure gauge will indicate present oil pressure. Normal oil pressure (greater than 6 psi) will display a value between 000 and 176. A low oil pressure (less than 6 psi) or an inoperative engine oil pressure switch will display a value greater than 176. dEGC Display of engine temperature in Degrees C input from cylinder head temperature sensor. If the value displayed is -40C, the SCP message for engine temperature has not been received for more than 5 seconds. GO to Pinpoint Test E .
  • 49 C="C" mark.
  • 60 C=Normal band start.
  • 120 C=Normal band end.
  • 119 C=Temperature warning indicator ON.
  • "-40" C=No SCP Message for 5 sec.
br Displays the brake fluid level input to the HEC. bAtt Displays the code (0-255) battery voltage input to the HEC. Battery voltage gauge will indicate present battery voltage.
  • 93-102=6.9-9.1 volts (Low voltage)
  • 115-124=8.5-10.7 volts (Norm band start)
  • 215-225=15.8-18 volts (Norm band end)
  • 230-241=16.9-19.1 volts (High voltage)
rhEo Displays the present hexadecimal value for the instrument cluster backlighting pulse width modulated (PWM) input to the HEC (used when requesting assistance from the hotline). rhi
rhS
rho PWM input duty cycle.
SCP hexadecimal dimming step (used when requesting assistance from the hotline).
Output driver counts in hexadecimal format (used when requesting assistance from the hotline). Cr Displays the present RUN/START sense input. Display will show -h with the ignition switch in the START position and -L with the ignition switch in the RUN position. ALtF Displays 8-bit hexadecimal value for alternate fuel level. Display will show a value between 00 and FF if the message is received. PA-PE7 Not used. GAGE Repeats test display cycle.
Turn the ignition switch to the OFF position or press and hold the SELECT/RESET button for 3 or more seconds and release to exit HEC Dealer Test Mode. If no DTCs related to the concern are retrieved, proceed to the Symptom Chart to continue diagnostics.

1999 Lincoln... | Answered on Sep 22, 2018


sounds like a bad power connection or dead battery. when you place a load on the system a poor connection or dead battery will allow voltage to drop below norms causing everything to shut down. when you release the key and the load is removed, some voltage returns to power the lights and displays.

1999 Lincoln... | Answered on Jan 26, 2018


sounds like a hub bearing is going bad well it is already bad most likely best place to start

1999 Lincoln... | Answered on Aug 03, 2017


well the system is ok your blender doors might not be opening or you your heater controls board is bad if your temp gauge reads at half way mark

1999 Lincoln... | Answered on Aug 02, 2017


Hey Leigh.
The firewall is the big thing that separates the engine from the cabin,, its the thing the dash is bolted to. I WOULD HIGHLY RECOMMEND TAKING THIS TO A RADIATOR SHOP/AUTO REPAIR SHOP, tell them your story, and then ask the them how much they would charge you to cut and splice the heater hoses. The hoses run through the firewall somewhere in front of where the passenger sits, the hoses run from the radiator... then have valves and connectors in them. you will need some type of female to female connector and two hose clamps..YOU MUST do this when the engine is COLD.. you don't want to attempt this with HOT antifreeze!! This is not something you can do without a fair amount of knowledge about how automotive A/C and heater systems work.. Once you can identify the correct hoses... it won't be hard..you could actually bypass ALL the valves and connections.. Find the two hoses that come from the radiator and splice them together when you find a length of hoses that will facilitate a connection loop.. please rate as helpful..

1999 Lincoln... | Answered on Jul 18, 2017


my 2011 navigator won't start just installed new battery and all i am getting is a load clicking sound

1999 Lincoln... | Answered on Jul 07, 2017


yes sure you can I do it all the time just a conversion kit which is springs and shocks or just get shocks

1999 Lincoln... | Answered on Jul 01, 2017


celunoid ?? SOLENOID ! Could be starter , test ! VOLTAGE DROP TESTING .

Starter Voltage Drop

What size engine ???
Starter Motor, 4.6L C1020
Lower right side of engine
Starter Motor, 5.4L C1020
Lower right side of engine


Starter Motor Relay, 4.6L C166
Right rear of engine compartment
C167
Right rear of engine compartment
Starter Motor Relay, 5.4L C166
Right rear of engine compartment
C167
Right rear of engine compartment

1999 Lincoln... | Answered on Jun 23, 2017


103 50A: Battery junction box
501 30A: ? Might be a circuit breaker

1999 Lincoln... | Answered on Mar 15, 2017

Not finding what you are looking for?

570 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Lincoln Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

gerry bissi

Level 3 Expert

4388 Answers

fordexpert

Level 3 Expert

5692 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Navigator Lincoln

  • Navigator Lincoln

Most Popular Question

our 1999 lincoln navigator not

  • Cars & Trucks
Loading...