Top 10 2005 Hyundai Santa Fe Questions & Answers

This is from the factory service manual of your car:
There is no onboard programming procedure for this vehicle. This vehicle requires special equipment be connected to the vehicle to program the keyless remote. Translation you need the dealer to do this.

Below are instructions and a diagram for removing the radiator from your Santa Fe. There's nothing involving the motor mounts. Best of luck and please post back with any questions or just to rate the solution. Greg

1. Drain the cooling system. Remove the radiator cap to speed draining.
2. Remove the inlet hose from the radiator.
3. Remove the transmission oil cooler lines from the retainer clip at the bottom of the cooling fan shroud.
4. Remove the fan shroud clip from the condenser tubes.
5. Remove the bolt that connects the fan shroud to the condenser hold down bracket.
6. Remove the air deflectors from the top of the radiator.
7. Remove the cooling fan shroud bolts.
8. Remove the coolant reservoir hose from the radiator overflow neck.
9. Remove the radiator upper support brackets and bolts that connect to the fan shroud.
10. Disconnect the engine cooling fan motors electrical connectors.
11. Remove the cooling fan motors electrical harness from the fan shroud clips.
12. Remove the cooling fan shroud.
13. Remove the outlet hose from the radiator.
14. Disconnect the transaxle oil cooler pipes from the radiator.
15. Tilt the top of the radiator rearward.
16. Remove the condenser hold down bracket from the radiator.
17. Lift the condenser from the mounting tabs on the radiator and position the condenser aside.
18. Remove the radiator.

Definition of P0171 is Applied to All Manufacturers Powertrain: System Too Lean Bank 1
Definition of P0174 is Applied to All Manufacturers Powertrain: System Too Lean Bank 2

Well, you basically have only 3 choices:
1. Pay the fee at the dealership
2. Purchase the high-dollar equipment that is required to perform the programming procedure
3. Forget about adding another key fob to tor vehicle.

TECHNICAL SERVICE BULLETIN

Group
90 - ELECTRICAL

Number
03-90-020

Date
October, 2003

Model
Elantra 2001-2004, Santa Fe 2001-2004, Sonata 2002-2004, Tiburon 2003-2004, XG(NNN) NNN-NNNNand XG(NNN) NNN-NNNN2004

Subject
SECURITY SYSTEM KEYLESS ADAPTER CABLE

This bulletin supersedes TSB # XXXXX
DESCRIPTION:
The security system keyless adapter cable (SPX/Kent-Moore P/N 09900-21300) is a special service tool (SST) that is used for programming new keyless entry remote transmitters to the factory security systems. The keyless adapter is used in conjunction with the Hi-Scan Pro (with Hi-Scan SOL Pro Software Version 09-29-03 or newer) and Data Link Connector (DLC) Cable.
SERVICE INFORMATION:
The keyless adapter cable can be used on the following vehicles:
^ 2001 -2004 Elantra
^ 2001-2004 SantaFe
^ 2002 - 2004 Sonata

I bought a smaller belt put on but heat won't work?

this link might help you out.
How to replace crankshaft position sensor on 2005 santa fe Google Search

How to replace crankshaft position sensor on 2005...

google.co.uk

On a 2005 Santa Fe with a 2.7 L engine it is located on air breather side. Air breather needs to be removed to get to it.

don't think you can buy the ring but if so tap it on with a brass drift after cleaning the rust from the housing might be cheaper to get a remain axle

Lets narrow this down a bit. You said all 4 wheels lock up. So the problem will will have a part in all 4 wheels. So knowing that, we can forget about the hose, master cylinder, and brake booster theories. It sounds like the ABS module is malfunctioning and surging. The Santa Fe's in the previous year had the same problem and were recalled. The problem with those was the ABS unit. Hope this helps you.

Bottom of the engine, near the rear. You can follow the cables from your battery, very large cable that runs down near the firewall.