Top 20 2006 Land Rover Range Rover Sport Questions & Answers


Hi, I would certainly say this is a fuse problem you should have checked these first, hope this helps. Please leave me feed back: Malcolm Campbell, Thanks.

2006 Land Rover... | 113 views | 0 helpful votes


Hi, They are connected look at fuse's this may be the problem. Please leave me feedback, Malcolm Campbell.

2006 Land Rover... | 111 views | 0 helpful votes


Check for breaker fuse under hood.

2006 Land Rover... | 53 views | 0 helpful votes


If the compressor has to run more than normal, there is likely a fault / leak in the system somewhere which these are notorious for. Check your airbags for leaks / spray all parts with a mist of water and soap to find where your air is escaping from.

2006 Land Rover... | 189 views | 0 helpful votes


It's supposed to do that. Audio confirmation of locking.

2006 Land Rover... | 64 views | 0 helpful votes


Published: 11-May-2011
Engine - V8 4.4L Petrol - Crankshaft Pulley
In-vehicle Repair
Special Tool(s)

Holding Tool Crankshaft Pulley
303-893(LRT-12-080)
Adapter
303-191-03
Bolts and spacers
303-191-04
Remover, crankshaft pulley
303-588
Remover, crankshaft seal
303-D121
Installer, crankshaft seal
303-1100
Adapter - Crankshaft seal installer
303-1100-01 Removal
  1. Disconnect the battery ground cable.
    For additional information, refer to: Specifications (414-00 Battery and Charging System - General Information, Specifications).
  1. WARNING: Do not work on or under a vehicle supported only by a jack. Always support the vehicle on safety stands. Raise and support the vehicle.
  1. Remove the accessory drive belt.
    For additional information, refer to: Accessory Drive Belt (303-05B Accessory Drive - V8 4.4L Petrol, Removal and Installation).

  1. Remove the cooling fan shroud.
    • Release 2 clips from the cooling fan lower shroud.
    • Release and remove the cooling fan lower shroud from the cooling pack.

  1. Using the special tools, retain the crankshaft pulley.
  1. CAUTION: Under no circumstances should the crankshaft setting peg, 303-645, be used in the following operations, to restrain the crankshaft. NOTE: The crankshaft pulley retaining bolt will be very tight.
    Remove the crankshaft pulley retaining bolt.
    • Discard the bolt.
  1. Remove the special tools.

  1. Using the special tools, remove the crankshaft pulley.
    • Collect the locking ring.
  1. Remove the special tools from the crankshaft pulley.

  1. Using the special tool, remove the crankshaft front seal.
    • Remove the outer section of the seal.
    • Repeat the process to remove the inner section of seal.
  1. Check the crankshaft damper pulley and locking ring for damage.
Installation
  1. Clean all the crankshaft pulley mating faces.

  1. Using the special tools, install the crankshaft front seal.
    • Lubricate the seal with clean engine oil.
    • Use the discarded crankshaft bolt with the service tool.
  1. Install the crankshaft pulley.
    • Lubricate the seal with clean engine oil.
  1. Install the crankshaft pulley locking ring.
  1. CAUTION: The screw thread in the crankshaft pulley must be cleaned out before installing a new crankshaft pulley bolt. Install, but do not tighten, the new crankshaft pulley bolt.
  1. CAUTION: Under no circumstances should the crankshaft setting peg, 303-645, be used in the following operations, to restrain the crankshaft. Using the special tools, retain the crankshaft pulley.
    • Tighten the crankshaft pulley bolt to 380 Nm (280 lb.ft).
  1. Remove the special tools.
  1. Install the cooling fan lower shroud.
  1. Install the accessory drive belt.
    For additional information, refer to: Accessory Drive Belt (303-05B Accessory Drive - V8 4.4L Petrol, Removal and Installation).
  1. Connect the battery ground cable.
    For additional information, refer to: Specifications (414-00 Battery and Charging System - General Information, Specifications).

2006 Land Rover... | 283 views | 0 helpful votes


Can you feel some hard jerking passing on bumpy road? Have the suspension checked.

2006 Land Rover... | 3,206 views | 0 helpful votes


then would one not presume the motor has failed .but check for a loose plug under the seat .

2006 Land Rover... | 106 views | 0 helpful votes


Got power coming OUT of the switches when actuated? If so - is power going into the motors when actuated by switches?

2006 Land Rover... | 89 views | 0 helpful votes


rOFLOL some vehicles have a memory setting for the seat position .perhaps yours got confused .

2006 Land Rover... | 139 views | 0 helpful votes


Passenger door has a cover if removed it exposes the manual key insert to open the door with the ignition key

2006 Land Rover... | 86 views | 0 helpful votes


the transmission control module has to be programmed to the vehicle using suitable diagnostic equipment. the code you have got i suspect is telling you that, all the modules on modern vehicles communicate with each other via. the can and scp networks to work correctly. if that has not been done, that is more than likely the problem, or the road speed signal may be missing but i suspect you would have other fault codes logged. hope this helps. ps. i worked for a jaguar franchise before i retired, they use the same systems, same company.

2006 Land Rover... | 253 views | 0 helpful votes


You might find it cheaper to replace CD , than get it repaired , check it out , look at Yellow Pages for local repairer.

2006 Land Rover... | 89 views | 0 helpful votes


Setting is on your Sat Nav, Check " Setting Section "

2006 Land Rover... | 302 views | 0 helpful votes


Hi Diane, from the symbol you described it sounds like you are not receiving the satellite signal to your sat nav! The weak satellite signal could be due to the location you are in and also within the vehicle, some vehicles reduce satellite signals and you have to fix an external aerial to improve the signal! Have you tried using it with the door/ window open to see if that helps the signal?

2006 Land Rover... | 486 views | 1 helpful votes


If I read right you just want to raise the air suspension and solenoid valves jumper the air compressor and it will fill the airbags

2006 Land Rover... | 107 views | 0 helpful votes


Yes you can. If the battery is connected thenn you should be able to get power to the mini compressor under the spare wheel. Just turn the car to the on position and use as normal. Remember you have to ahve battery power.

2006 Land Rover... | 79 views | 0 helpful votes


The brake light fuse lives in the boot on a Range Rover Sport - lift the access panel and its on the Left side in a bank of 4-5 fuses immediately neighbouring the jack slot.

2006 Land Rover... | 553 views | 0 helpful votes

Not finding what you are looking for?
Cars & Trucks Logo

342 questions posted

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Marvin
Marvin

Level 3 Expert

85020 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Range Rover Sport Land Rover

  • Range Rover Sport Land Rover

Most Popular Question

sat nav not showing me in correct

  • Cars & Trucks
Loading...