20 Most Recent 2006 Land Rover Range Rover Sport - Page 2 Questions & Answers


It's supposed to do that. Audio confirmation of locking.

2006 Land Rover... | Answered on Aug 15, 2016


Published: 11-May-2011
Engine - V8 4.4L Petrol - Crankshaft Pulley
In-vehicle Repair
Special Tool(s)

Holding Tool Crankshaft Pulley
303-893(LRT-12-080)
Adapter
303-191-03
Bolts and spacers
303-191-04
Remover, crankshaft pulley
303-588
Remover, crankshaft seal
303-D121
Installer, crankshaft seal
303-1100
Adapter - Crankshaft seal installer
303-1100-01 Removal
  1. Disconnect the battery ground cable.
    For additional information, refer to: Specifications (414-00 Battery and Charging System - General Information, Specifications).
  1. WARNING: Do not work on or under a vehicle supported only by a jack. Always support the vehicle on safety stands. Raise and support the vehicle.
  1. Remove the accessory drive belt.
    For additional information, refer to: Accessory Drive Belt (303-05B Accessory Drive - V8 4.4L Petrol, Removal and Installation).

  1. Remove the cooling fan shroud.
    • Release 2 clips from the cooling fan lower shroud.
    • Release and remove the cooling fan lower shroud from the cooling pack.

  1. Using the special tools, retain the crankshaft pulley.
  1. CAUTION: Under no circumstances should the crankshaft setting peg, 303-645, be used in the following operations, to restrain the crankshaft. NOTE: The crankshaft pulley retaining bolt will be very tight.
    Remove the crankshaft pulley retaining bolt.
    • Discard the bolt.
  1. Remove the special tools.

  1. Using the special tools, remove the crankshaft pulley.
    • Collect the locking ring.
  1. Remove the special tools from the crankshaft pulley.

  1. Using the special tool, remove the crankshaft front seal.
    • Remove the outer section of the seal.
    • Repeat the process to remove the inner section of seal.
  1. Check the crankshaft damper pulley and locking ring for damage.
Installation
  1. Clean all the crankshaft pulley mating faces.

  1. Using the special tools, install the crankshaft front seal.
    • Lubricate the seal with clean engine oil.
    • Use the discarded crankshaft bolt with the service tool.
  1. Install the crankshaft pulley.
    • Lubricate the seal with clean engine oil.
  1. Install the crankshaft pulley locking ring.
  1. CAUTION: The screw thread in the crankshaft pulley must be cleaned out before installing a new crankshaft pulley bolt. Install, but do not tighten, the new crankshaft pulley bolt.
  1. CAUTION: Under no circumstances should the crankshaft setting peg, 303-645, be used in the following operations, to restrain the crankshaft. Using the special tools, retain the crankshaft pulley.
    • Tighten the crankshaft pulley bolt to 380 Nm (280 lb.ft).
  1. Remove the special tools.
  1. Install the cooling fan lower shroud.
  1. Install the accessory drive belt.
    For additional information, refer to: Accessory Drive Belt (303-05B Accessory Drive - V8 4.4L Petrol, Removal and Installation).
  1. Connect the battery ground cable.
    For additional information, refer to: Specifications (414-00 Battery and Charging System - General Information, Specifications).

2006 Land Rover... | Answered on Jan 27, 2016


Got power coming OUT of the switches when actuated? If so - is power going into the motors when actuated by switches?

2006 Land Rover... | Answered on Nov 09, 2015


then would one not presume the motor has failed .but check for a loose plug under the seat .

2006 Land Rover... | Answered on Nov 09, 2015


rOFLOL some vehicles have a memory setting for the seat position .perhaps yours got confused .

2006 Land Rover... | Answered on Aug 31, 2015


You might find it cheaper to replace CD , than get it repaired , check it out , look at Yellow Pages for local repairer.

2006 Land Rover... | Answered on Apr 25, 2015


the transmission control module has to be programmed to the vehicle using suitable diagnostic equipment. the code you have got i suspect is telling you that, all the modules on modern vehicles communicate with each other via. the can and scp networks to work correctly. if that has not been done, that is more than likely the problem, or the road speed signal may be missing but i suspect you would have other fault codes logged. hope this helps. ps. i worked for a jaguar franchise before i retired, they use the same systems, same company.

2006 Land Rover... | Answered on Mar 19, 2015


Yes you can. If the battery is connected thenn you should be able to get power to the mini compressor under the spare wheel. Just turn the car to the on position and use as normal. Remember you have to ahve battery power.

2006 Land Rover... | Answered on Mar 05, 2015


Setting is on your Sat Nav, Check " Setting Section "

2006 Land Rover... | Answered on Feb 24, 2015


Sometimes it does and sometimes it doesn't.

2006 Land Rover... | Answered on Jan 21, 2015


Hi Diane, from the symbol you described it sounds like you are not receiving the satellite signal to your sat nav! The weak satellite signal could be due to the location you are in and also within the vehicle, some vehicles reduce satellite signals and you have to fix an external aerial to improve the signal! Have you tried using it with the door/ window open to see if that helps the signal?

2006 Land Rover... | Answered on Jan 11, 2015


Make sure you have it connected properly. If so check your maxi fuse in case something grounded or the battery wasn't disconnected during the removal or reinstall. Make sure you have a fully charged battery.and that your battery leads are not corroded up the strand.

2006 Land Rover... | Answered on Dec 29, 2014


I believe you will find the MAF sensor in similar locations on your LR3 as with P38. In the intake tube between your air filter and the engine there will be a section that has a multi-long-running to it. This middle section of the air intake houses your MAF sensor. This is a fairly fragile component, use care in handling, do not touch the wire or mesh and clean only as specifically instructed on the label of the product formulated specifically for cleaning it.

2006 Land Rover... | Answered on Dec 29, 2014


Do NOT delay in getting this checked. It may be something simple, but it could also be potentially dangerous. See the articles on the website www.graemecooper.com.au about identifying noises

2006 Land Rover... | Answered on Sep 25, 2014


1) mostly caused by leakakage in airbag.in that case get it scanned on a computer and it will confirm this with a error code.not a very expensive problem.

2) the other most common is failure of the compressor to pump the system to pressure in a set time due to wear. There are also failures of the air springs, the module and so on. If the compressor is the fault, only a replacement will solve the problem. its bit expensive but still a affordable one.not a big issue.

This will help. Thanks please keep updated.please do rate the solution positively .thank you for using fixya.

2006 Land Rover... | Answered on Jul 14, 2014


check for faulty hydraulic lifter/s Check for correct viscosity of oil. Check for correct type of oil filter ( must have an anti-drain back valve in the filter.)

2006 Land Rover... | Answered on Jun 07, 2014

Not finding what you are looking for?
Cars & Trucks Logo

342 questions posted

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Range Rover Sport Land Rover

  • Range Rover Sport Land Rover

Most Popular Question

sat nav not showing me in correct

  • Cars & Trucks
Loading...