Hyundai Motor 2005 XG350 - Answered Questions & Fixed issues

between 800-950 rpm a/c on in park ,there is a relearn procedure if battery was replaced but a scan tool must be hooked up to perform it at dealership

Safety feature in case you forget to lock the car? I'm guessing it doesn't lock whilse you are driving the car or have the ignition on? Most modern cars have this feature. Don't forget your keys in the car. Learnt the hard way a while ago!

Have to get the trouble codes read first. See this post on airbag lights. http://ricksfreeautorepairadvice.com/why-is-my-airbag-light-on/

check junk yards 10 bucks

Are you asking about air con or about a compressor to supply air for blowing things up like tyres? It is possible that a short circuit is still happening in the lighter / power socket. Make sure that all fuses and relays are working.

Splice the camera power wire into one of the backup light bulb sockets at the rear of the car. Make sure there is a good ground connection to the camera housing too. It's best to add a ground wire so there will never be a power problem at the camera.

you should have pwr w the key on at all times at that fuse. Bad relay or short in ignit system.

Check inertia switch..... may need reset. don

No offense, in my opinion, if your not properly trained DONT DO IT. take it in. Sorry, Frank M

Hi there my name is Brandon I am a mechanical n electronic engineering technician it could be a few things I will need more information to help you better get back to me on heir and I will help you

Hi Pamela: Have a look at this youtube clip. https://www.youtube.com/watch?v=24iVN1-vkac Cheers.

It can be the module and it may be a bad connection, as in corrosion, backed out or loose pins in the connector and / or bad or corroded wiring .

-Always follow its repair manual. Good luck Mai

Hyundai XG350 alarm module Questions & Answers - Fixya

www.fixya.com > ... > Tags > alarm module > Cars & Trucks > Hyundai Hyundai XG350 cars & trucks alarm module questions and answers. Ask your Hyundaialarm ... TURN IGNITON TO ON 4. WAIT 5 ... Hyundai Motor 2005 XG350.

All the exterior lights run threw the turn signal switch. Except the high mount brake light. If you are talking about brake lights replace the TS switch. Parking lights are a little different. If you have no parking lights front and back, TS switch. If you have front and no back, ground problem. Grounds for the back are usually on the drivers side mounted to the frame.

Such as?

check the firing order of the leads when you changed the plugs.

P0320 Hyundai Ignition/Distributor Engine Speed Input Circuit Possible causes - Faulty Ignition/Distributor engine speed sensor - Faulty Crankshaft Position sensor - Ignition/Distributor engine speed sensor harness is open or shorted - Ignition/Distributor engine speed sensor circuit poor electrical connection - Low battery charge - Faulty Engine Control Module (ECM) What about the obd code? The P0320 Hyundai code is triggered when the Engine Control Module (ECM) detects that there is no current at the ignition coil group Symptoms - Engine Light ON (or Service Engine Soon Warning Light) - Lack/Loss of Power - The engine may be harder to start - The engine may stumble or stall P0320 Hyundai Description Ignition failure sensor is used to check whether the spark ignition is occurred correctly or not and also used to tachometer drive. The sensor monitors the voltage difference between a resistance which is on the battery circuit for ignition coil. When the ignition coil works properly, the electric current through the resistance is detected as voltage drop. This is confirmed for every ignition event with the crankshaft sensor and the camshaft sensor. If ECM detects a malfunction, no ignition is possible, so the engine would not start. If there is no ignition signal for a predetermined cycle for one or two ignition coils, an ignition coil circuit failure exists.

If your somewhat machnically incline to do small projects this is one. cool engine and drain at least half of the coolant. (I usually replace all of my coolant at this time) remove the intake air cleaner hose from the air cleaner filter housing and the throttle body intake to make room. follow the upper radiator hose from the radiator to the water inlet cap and remove the three screws and tap it loose.( nows a good time to inspect hose to see if it's time to replace) pop out the old thermostat and in with the new. make sure surface is clean. make sure the rubber gasket is snug around the new thermostat and make sure the thermostat vent is on the top. tighten to 15 lbs. and replace intake hose and refill coolant. verify no leaks. Hope this helps

• I have a 2002 XG and they should be the same but the front 3 are easy but for the back 3 you'll need to take off the intake manifold so you will need a gasket kit for the manifold. if you are not that mechanically inclined u may want a mechanic to handle that. if u have a miss make sure it's not the ignition coils on top of the front 3 spark plugs. i made the mistake of replacing all of my spark plugs @180,000 miles to find out the miss was from one of my ignition coils.
• good luck