20 Most Recent 2001 Hyundai Tiburon - Page 3 Questions & Answers

https://www.youtube.com/watch?v=us5jqmhHus8 see if this does it for you man

Chances are the dome light is grouped into a circuit for other lights as well. You should have a "meter" or "head" listing in the fuse box. One of these should do it. The fuse box should be under a kick panel below the steering wheel on the left side.

Is the carpet getting wet on the passenger floorboard? Are you getting an oily film on the inside of the windows? Might be a heater core leak.

It has to do with Fuel Trim and O2 sensor readings, based on whether the vehicle is under load, running rich or lean, and what state the PCM is in for correction. I tried to paste the full answer, but Fixya's systems will not allow it (it is quite lengthy). The short answer: O2 sensor and/or MAF sensor.

having the same problem... my car is an 03 as well... any solution yet? i flushed my tranny, put in synthetic, made sure the linkages were lubricated inside and outside the car, and still nothing.. theres no grinding, at all, its just really gummy

1.5L And 1.6L Engines



Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L DOHC engines




Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L SOHC engines



1.5L Engines



Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L DOHC engines




Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L SOHC engines




Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L SOHC engines, 1.6L similar



1.8L (VIN M) And 2.0L (VIN F) Engines



Fig. Proper alignment of the timing belt alignment marks for belt removal and installation-Hyundai 1.8L and 2.0L (VIN F) engines



2.0L (VIN P) Engines



Fig. Oil pump and crankshaft inner timing belt sprocket alignment marks-Hyundai 2.0L (VIN P) engines




Fig. Timing belt sprocket alignment mark locations and positioning for belt removal and installation-Hyundai 2.0L (VIN P) engines



3.0L (VIN G)



Fig. Installation of the timing belt-3.0L (VIN G) engine







Fig. Timing belt sprocket alignment mark positioning for belt removal and installation-Hyundai 3.0L engine


Hope this helped (remember comment and rated this post).

there are only four possibilities left: 1: valves are not fully seating - adjust rocker arm / cam 2: piston rings are bad - replace rings 3: holes in pistons - replace 4: cylinders out of round - most complicated repair, bore / machine cylinders and replace piston rings with oversized rings. of course you could just have 'gunk' on the valves preventing full closure........

Your really not giving too much information about your problem so if you could be more specific that may help. Off hand I would think that one of the sensors or switches. like the trunk, windows or even the hood may be either corroded of bad.

a crank sensor will make you not get a signal to trigger the power for the coil so that may be the problem with it. If all else is ok, is the check engine light on to scan it for the crank sensor code.

Had the same problem and the motor is pricey. We went to a junk yard and found the same car and bought the door. We took it to a local small mechanic and he took the one and replaced it to ours. Never had another problem with the window, If you can find the same card in a junk yard it would be the cheapest way. hope that helps.

clutch

There is a problem with the filler neck hose or the vent hose. This is not something that is for a casual mechanic to fix.

you haven\'t refitted the gear change cables properly

Most people don't own a torque wrench that goes past 150 lbs & you can't push it that far So if the nut was say 180 or 206 you have to stop at 140 & then use a 3 foot 3/4 drive bar or ratchet & go another 1/8 turn. Google the question,should be there

What is the question other than the Brake Caliper has been replaced

Caliper Piston is probably starting to cease up or possibly a flex line collapse which will allow the brake fluid through but won't allow it to return.After sitting it will slowly release.

Check the transmission fluid level