Top 10 2001 Hyundai Sonata Questions & Answers

2001 Hyundai Sonata Logo

Question

  • 4,442 People Helped

Door locks don't work

The door locks on my 2002 Hyundai Sonata don't respond to the door switch or the remote when trying to lock the doors. The remote will unlock all doors but will not lock the doors. The door switch will not lock or unlock the doors. Someone suggested replacing the door lock relay. I cannot gain access to the door lock relay as it appears to be behind the fusebox under the lower left dash panel. Does anyone know how to remove the dash panel to access the relays or is there an easier way to replace the door lock relay?

Greg

Posted by on

Answer

  • Most Helpful of 4 Answers

Disassemble the paneling on left side ,under the steering wheel. Remove all screws and pull out the panel until you can you can reach behind it to remove the two Black Relays, on the side closest to Steering wheel. Remove the Relay covers, Clean the contacts with a 1/8 fine strip of 600 wet/dry sand paper. Only place the paper between the contacts, and pull out while holding slight pressure on the relay Armature. Turn over the sandpaper and repeat once again. Very gently press the TOP resting contact pad closer to the armature, to lessen the gap between the contact points, so the armature doesn't have to travel as far to reach the closed contact position. Repeat the above with the other2nd Relay. Replace the covers, reinstall the relays And test the Door locks prior to buttoning up the paneling. Note, a pair of long needle nosed pliers will help in removing the relays. Just Grip the relay and rock in Forward and Backward as you apply upward pressure.

Posted on Oct 09, 2008

Question

  • 2,334 People Helped

engine code p0421

2001 hyundai sonata engine lights on being found out for engine code p0421







Posted by on

Answer

  • Most Helpful of 1 Answers

Catalyst System Efficiency Below Threshold (Bank 1)

The catalytic converter has an oxygen sensor in front and behind it. When the vehicle is warm and running in closed loop mode, the upstream oxygen sensor waveform reading should fluctuate. The downstream O2 sensor reading should be fairly steady. Typically the P0420 code triggers the Check Engine Light if the readings of the two sensors are similar. This is indicative of (among other things) a converter that is not working as efficiently as it should be (according to specs). It is part of the vehicle emissions system.

A code P0420 may mean that one or more of the following has happened:

* Leaded fuel was used where unleaded was called for
* An oxygen sensor is not reading (functioning) properly
* The engine coolant temperature sensor is not working properly
* Damaged or leaking exhaust manifold
/ catalytic converter / exhaust pipe
* Retarded spark timing
* The oxygen sensors in front and behind the converter are reporting too similar of readings


To Do list

* Check for exhaust leaks at the manifold, pipes, catalytic converter. Repair as required.
* Use a scope to diagnose the oxygen sensor operation (Tip: The oxygen sensor in front of the catalytic converter normally has a fluctuating waveform. The waveform of the sensor behind the converter should be more steady).
* Inspect the downstream heated oxygen sensor (HO2), replace if necessary
* Replace the catalytic converter

Posted on Jan 19, 2009

Question

  • 2,716 People Helped

Evap Code p0455 2000 Mitsubishi Eclipse

Evap Code p0455 2000 Mitsubishi Eclipse......I replaced the gas cap and the check engine soon light came on. The monitors take awhile to clear though....sometimes its days before the light comes back on.

Posted by on

Answer

  • Most Helpful of 1 Answers

check the vent solenoid it is located on the vapor cannistor by the gas tank

Posted on Jul 02, 2009

Question

  • 2,789 People Helped

Engine revs up to 3000-4000 rpm all by itself

Yesterday, I was driving at about 40-45 mph, and all of a sudden the engine revs up to 3000-4000 rpms.  I come to a stop light the engine is still at that same high level of rpms with my foot on the brake.  I found that when I was going up a steep hill, I didn't need to put my foot on the accelerator because I was coasting just fine up a hill at 45 mph.  We parked the car and it wouldn't turn back on.  After not touching it for 30 minutes, we came back to the car and the check engine light was on and the problem was gone.  I have a 2001 Hyundai Sonata Automatic V6.

Posted by on

Answer

  • Most Helpful of 2 Answers

THERE IS A TEMPERATURE SENSOR ON MOTOR WHICH CAUSES THIS PROBLEM... USUALLY IT SHOWS A NEGATIVE TEMP READING WHICH CONFUSES THE COMPUTER CAUSING IT TO REV UP....HAVE THE ENGINE DIAGNOSED ON A SCANNER....GOOD LUCK...

Posted on May 25, 2009

Question

  • 2,473 People Helped

Power antenna broke and I need to replace it. How

Power antenna broke and I need to replace it. How do I do this

Posted by on

Answer

  • Most Helpful of 1 Answers

Buy replacement antenna mast. Remove old one by unscrewing the retaining cap nut. Turn on the radio & let the antenna cable run all the way up while you pull on it to remove it.
Install the new antenna mast by turning the radio 'off' so the spool inside goes back to its beginning while you feed the cable of the new antenna down into the antenna mast hole.
Once the cable is all the way down, reinstall the retaining nut/cap and turn on the radio to allow the spool to run the antenna 'UP.'... cycle the radio ON and then OFF several times allowing the antenna to move all the way up and all the way down.
That's it!

Posted on Oct 04, 2009

Question

  • 3,251 People Helped

How to set the clock for a Hyundai Getz?

How do you set the clock for a Hyundai Getz? It's on the dashboard, and I can't see any buttons to fiddle with.

Posted by on

Answer

  • Most Helpful of 1 Answers

hi from uk ! to set clock/time on getz look t the speedometer ? you will see two buttons on the bottom of dial ? the left button is to cancel the trip meter by pressing button in for trip A and again for B trips the right hand button marked hr + min ? to set hour time turn to left untill hr time is shown then release now turn button to right to set the minutes then releas when time/minutes ar correct that is it! ps you cannot cancel the odometer/milage clock only trip meter hope this helps best wishes from n/west uk

Posted on Oct 16, 2009

Question

  • 2,594 People Helped

where is the fuel pump relay located on a 2001

where is the fuel pump relay located on a 2001 hyundai sonata

Posted by on

Answer

  • Most Helpful of 1 Answers

there is 1 relay that controls the ECM / Fuel pump. its located above the center hump in the dash, right side. Like to the right and below radio area.

Posted on Oct 27, 2009

Question

  • 3,457 People Helped

how to replace rear wheel

how to replace rear wheel bearing on 2003 hyandia sonata

Posted by on

Answer

  • Most Helpful of 1 Answers

Hub & Bearing Removal & Installation To Remove:
Hub bearing assembly (Typical) hyundai-08-00-6029.gif

  1. Release parking brake.
  2. Remove rear wheel assembly.
  3. Remove rear wheel speed sensor from carrier.
  4. Dismount brake caliper and support with mechanic's wire.
  5. Remove brake disc.
  6. Remove 4 axle hub mounting bolts. Special tool 09432-11000 (Typical) hyundai-08-00-6021.gif

  7. Using tool 09432-11000 (or suitable gear puller), remove tone wheel.
  8. Remove carrier.
  9. Remove stakes and remove flange nut.
  10. Support bearing outer race flange and press rear axle hub out.
  11. Using tool 09432-11000 (or suitable puller), remove inner race from axle hub.
To Install:
Hub bearing assembly (Typical) hyundai-08-00-6029.gif

  1. Apply thin coat of grease to bearing contact surface and hub.
  2. Using and appropriate tool, press bearing into hub. CAUTION
    Do not press against outer race of wheel bearing.
  3. Install flange nut and stake nut until it meets concave portion of spindle.
  4. Install carrier.
  5. Use an appropriate tool to press tone wheel.
  6. Install hub/bearing assembly with rounded portion of outer race facing up.
  7. Install 4 hub/bearing assembly bolts and rotate hub to seat bearing.
  8. Measure wheel bearing starting torque with a spring balance or equivalent device.
    • Starting torque should measure 15.9 in lb (1.8 Nm) or less
  9. Install brake disc.
  10. Mount brake caliper.
  11. Install rear wheel speed sensor to carrier.
  12. Install rear wheel assembly.
prev.gif next.gif

Posted on Oct 28, 2010

Question

  • 2,756 People Helped

were is fuel filter located on 2001 hyundai sonata

were is fuel filter located on 2001 hyundai sonata

Posted by on

Answer

  • Most Helpful of 1 Answers

THe filter is located above the fuel tank beneath the rear seats

Posted on Dec 21, 2010

Question

  • 4,133 People Helped

Hyundai sonata speedometer not working

Hyundai sonata speedometer not working

Posted by on

Answer

  • Most Helpful of 1 Answers

If your speedometer of yours Hyundai Sonata is not working, then I have mentioned a link as well as a video which will guide you to solve the speedometer issue in the Hyundai Sonata,
Link
Hyundai Sonata Speedometer is not working Inspection Costs YourMechanic...
Video

Posted on Dec 22, 2017

1,032 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Hyundai Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Brad Brown

Level 3 Expert

19187 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

2001 Hyundai Sonata Sonata

  • 2001 Hyundai Sonata Sonata

Most Popular Question

am replaci g positive terminal need know

  • Cars & Trucks
Loading...