1995 Lexus LS 400 - Page 5 - Answered Questions & Fixed issues

Check your connections to to the battery and to to voltage regulator which is where one of the red cables from the battery leads to. Take it to your closest Advance auto to check the battery and alternator for free.

Most likely I would say is the tension idler or the largest pulley

$1500 to $2500

Chk the -- wire to the speakers.

it is not a fuse it is not caused by the shop, u have a fault in the electronic engine or emission controls, that is the only thing that turns on the check engine light.

For the LS400 1UZ-FE V8 the firing order is 1-8-4-3-6-5-7-2, RH from the front 2-4-6-8, LH from the front 1-3-5-7. The RH/LH of the engine is facing forward, in other words, from the drivers seat looking forward.

there are 2 of them. bank 1 and bank 2. bank 1 is the passenger side and bank 2 is the driver side. they are underneath the car and placed in front of the catalytic converter in the exhaust stream

Could be that the latch is already latched, or just needs a little lube (wd-40 works great) Have someone pull the hood release and look at the latch see if it moves or if it look to be closed you can ulatch it with a pen or pencil while someone pulls the hood release if that is the case.

check the vacum lines going to the brake booster. if everything is connected properly you may need a new booster.

the insturment cluster is bad. auto & truck electronics can fix it. 866-983-6688

insturment pannel is bad.

YOU WILL NEED THE RADIO CODE.. If you dont have the code you may call the dealer with your vin number, or the radio serial number. it may be in the owners manual, sometimes I write them on the owners manual in case the card gets lost, may look like a credit card.

your car engine need overhauling if it occur every day

remove trim around gear shift (carefully pry up) remove screw for cup holder, remove felt pad in lower console. remove 2 10mm bolts remove console.

this is best left to a professional front end shop, it requires expensive special tools, if u still want to do it let me know and I will give u the tools needed and instruction u need to proceed.

you have to remove the head lamp. there are 4 bolts that hold it in. you will have to remove ouyer marker lens first.1 screw on top and pull forward. clips hold lens pretty tight.

the fuel pump is in the fuel tank. look under the rear seat and you will see it.

what is the low side pressure?

I had the same problem, found out it was the filter which is located in the glove box, open the glove box and the back panel should lift up and out and u will see the white plastic guard for the filter, take it off and pull out the filter and replace it.

Remote Programming Instructions

1. Driver's door OPEN and unlocked, all other doors closed and locked.

2. Insert YOUR key in ignition, DO NOT TURN, remove key.

3. Using the MANUAL lock/unlock button ON THE DRIVERS DOOR, slowly press lock and unlock 5 times (count the lock 5 times and unlock 5 times).

4. Shut door.

5. Open door.

6. Using the lock/unlock button ON THE DRIVERS DOOR, slowly press lock and unlock 5 times (count the lock 5 times and unlock 5 times).

7. With the door open insert your key into the ignition, turn to on position (DON'T START), wait 5 seconds. Turn off and remove key.

8. Locks should cycle once (Car will lock and then unlock once). If they don't cycle or they cycle more than once, do steps 1-7 over.

9. Now using the remote, push lock button, hold for one second,
release. The locks should cycle once. If not, start over and go slower.

10. Close the door. Open the door. Press the lock button on the remote. The locks should cycle. Close the door. Press the lock button on the remote, the doors should lock. Press again and the doors should unlock.