20 Most Recent 1995 Honda Civic - Page 4 Questions & Answers

Leaking head gasket

I really need more information to help you. However it may be a retaining pin to hold the cable on it.

install a GPS in your car and use it for a speedometer Very cheap fix..

Hold on, I have it written down in my manual.. Let me go get it. tic-tock....tic-tock.....tic-tock.....Ok I'm back! it is 63522 use the preset buttons to enter the 5 digitcode. book says you will need the systems serial number. im pretty sure each car hasa different number. but i could be wrong. good luck

And what do you want to know! If you don't know how to test a vehicles systems, then your off to the local repair shop Have to do something, then come here with a problem & test results

The speed sensor might be bad. I used to own a 99 Mitsubishi Eclipse with the same symptons. The car will start, but will not pass the 1st or 2nd gear, the speedometer will be at 0. I replaced the speed sensor and all the problems went away.

The 50 amp main fuse should be able to be tested with a standard test light. If it has continuity then it is OK. If it is bad then replace it and retest. First thing that comes to mind on a Honda with your symptoms is a fail ignition distributor or bad ignition coil. I would advise you to test for spark at the spark plugs and if you have none, then start testing the distributor.

You said you baught a new pump, filter and relay, get a voltmeter or agitator and test each of the wires, if your not getting power to it then its probably a hot wire coming from your battery terminal or one of the wiring harnesses coming out of your firewall, you probably know that the fuel pump access panel is underneath the back seat so take it off, test the ground first with the car on then test each individual hot wire, if you find a faulty wire see if you can manually fix it, if not then run a hot wire from the source using speaker wire or something similar until it turns on for you at contact with the ran hot wire, just be sure that you do hav gas in the pump while testing wires just not enough to blow yourself up lol, otherwise you will burn out your fuel pump motor.

Are you earthing the body of the spark plug? Sorry, but I don\'t know what level of electrics or mechanics your at. If you hold the ht lead which is not advisable the spark will jump to its easiest route. Let me know we can then take it from there

timing belt book, public library, or use their database. if you repair engines and are asking this, thats a good place to verify your info. (and the belt must have broken).a technician would notice the position before disassembly. be aware,the valves may have bent. you may want the haynes manual. they can get you one. where i live i can get their chilton manual at home by typing in my library card number. engine repair has alot to it when you are replacing that belt on that kind of car. i suggest reading the book. you will want seals and a water pump too. i hope the 4 exhaust valves did not get bent

Soak around the plug with WD40 and use a Snap extension and ratchet or an air impact driver.

will be found on the passenger side either just under the lower dash or behind the kick panel to the side of the footwell depending on model

Depending on the year. You will most likely have to replace the blower fan resister which is just next to the fan and pretty easy to replace.

if the nut is stuck , way not get expert help.it will come of in the right hands (heat, and impact gun)or heat axle to about 200F. to 300fthe as it cools hit it with penetration oil. as it cools it may suck in the oil (physics trick)and now the impact gun. no shop air, makes hard work on any cars.so if no shop air, use a 1/2 drive or more breaker bar.and use a pipe extenson, most 1/2 will snap at over 150lbs.so 3/4" works better but the impact gun works best.you can youtube this > why not do that.?here is first google hit on hubshttp://www.partsgeek.com/catalog/1995/honda/civic/driveshaft_-ar-_axle/wheel_hub.htmlor here is honda real.what you need is obvious. if you just look at the real drawings.brake page and hub,http://www.hondaautomotiveparts.com/auto/jsp/mws/prddisplay.jsp?inputstate=5&catcgry1=CIVIC&catcgry2=1996&catcgry3=2DR+DX&catcgry4=KA4AT&catcgry5=FRONT+BRAKE+%281%29tell my how would you pass the hole hub thru the small, hole in the knuckle spindle.you going to buy a whole new axle and knuckle.http://www.hondaautomotiveparts.com/auto/jsp/mws/prddisplay.jsp?inputstate=5&catcgry1=CIVIC&catcgry2=1996&catcgry3=2DR+DX&catcgry4=KA4AT&catcgry5=KNUCKLE?????????????????

posted 32 times by me, and 1000 by others search. please

posted 31 times by me and 1000 others. search. please.