20 Most Recent 1984 Honda Accord Questions & Answers

with the engine running remove pos cable from battery and if it dies,bad alt.

Here you go. Link to fuse box diagram. https://www.google.com/url?sa=i&rct=j&q=&esrc=s&source=images&cd=&cad=rja&uact=8&ved=0CAcQjRw&url=http%3A%2F%2Fhonda-tech.com%2Fhonda-accord-1990-2002-2%2Ffuse-box-diagram-94-97-accord-2610816%2F&ei=yTVbVfzPF8nEsAWSgoOAAg&psig=AFQjCNFFjD-k_xRBnKbnW4SgkE9k6N9L-w&ust=1432126879490167 Link to list of what fuses protect. https://www.google.com/url?sa=i&rct=j&q=&esrc=s&source=images&cd=&cad=rja&uact=8&ved=0CAcQjRw&url=http%3A%2F%2Fhonda-tech.com%2Fhonda-accord-1990-2002-2%2Ffuse-box-diagram-94-97-accord-2610816%2F&ei=1TRbVdzbD4LutQX-_YCgBg&psig=AFQjCNFFjD-k_xRBnKbnW4SgkE9k6N9L-w&ust=1432126879490167

ever give it a tune up this decade? the 60,000 mile service? can right foot action, avoid this stall, (yes, no ) key question, on all stalls.. is the EGR valve clean? it must not stick open.

good luck with that.what country, what is the question?how to remove ithow to buy it or where?how to overhaul it. how to buy the carb kit.how to use a custom carb. like a harley CV? or weber.what/?

Might be fuel pump. Mass air flow sensor

You may be hearing the starter gear that's engages the flex plate/fly wheel turn but not actually coming out engaging

Could damaged flywheel teeth where starter mesh. Turn the motor by hand a half turn and then try starter again. Does the vehicle start when you push or tow it?

Air cleaner housing.Chances are that Accord is carbureted. If the missing hose is a large diameter, that goes down to the exhaust, that is merely for cold starting in the winter, to speed up warming up the engine during the 'choke' cycle, and would not affect daily drivability.

There could be several causes for this. There could be a faulty fan motor, a bad temperature switch, or something like a broken or grounded wire. What have you checked so far?

Check for defective spot welds around the plastic inserts on the left and right sides of the trunk. If the spot welds burnt through the metal, there will be holes were water can get in. Use some JB Marine Weld to seal up any holes or cracks in the sheet metal. Also, check the rubber drain holes under those inserts, that are in the sheet metal of the car, to make sure they are not blocked with road dirt. Also, check the weather stripping on the outside of the car, adjacent to the trunk. If the rubber and chrome trim weather stripping is pulling out (on the exterior of the rear quarter panel), then water will leak through the little plastic attaching screws and into the trunk beneath the plastic containers on the left and right front sides of the trunk.

Not terribly familliar with honda cars but most systems use either a cold start injector or just richen up mixture through the normal fuel system. This is controlled by a temperature sensor, either separate from or part of dash gauge sensor. I'd begin looking for that. If its always in "cold start" if will give you symptoms like yours. If not fuel injected, check choke operation. This may not be a "cure" but it's a good place to begin looking!

The oil filter is located on the rear top side of the engine under the intake manifold. Access to it is best gained from under the vehicle