20 Most Recent 1998 Volvo V70 - Page 9 Questions & Answers

Brandonlo168,

The fuel filter can be located under the carpeted cargo storage floor at the rear of the wagon. Remove the four 10mm bolts, remove the cover. You will then see a removeable plate to the right just behind the rear passenger seat. Fuel filter can be seen through hole in hole. Replaced from underneath wagon. Be sure to make sure lines are fully inserted onto filter. Check for leaks. No smoking, extinguisher handy. Note arrow on filter for correct fuel flow.

Ron

Volvo V70TDI 1998 starts slowly at -2 glow plughs are working, still got with fumes after the car stated;
What to do??

The fuel filter can be located under the carpeted cargo storage floor at the rear of the wagon. Remove the four 10mm bolts, remove the cover. You will then see a removable plate to the right just behind the rear passenger seat. Fuel filter can be seen through hole in hole. Replaced from underneath wagon. Be sure to make sure lines are fully inserted onto filter. Check for leaks. Note arrow on filter for correct fuel flow. Good luck and hope this helps and no smoking please LOL

Chilton Book, best purchase ever...

You should first try to buy a new cap and new take the cap off while car is hot. The steam will cause the seal not to work anymore. Know from experience.

DTC P0305 Code - Cylinder #5 Misfire Detected
A P0305 code means that the the car's computer has detected that one of the engine's cylinders is not firing properly. In this case it's cylinder #5.

Symptoms may include the engine may be harder to start, the engine may stumble / stumble, and/or hesitate or other symptoms may also be present. Other tips to solve it in the previous fault code link.

A code P0305 may mean that one or more of the following has happened:
Faulty spark plug or wire
Faulty coil (pack)
Faulty oxygen sensor(s)
Faulty fuel injector
Burned exhaust valve
Faulty catalytic converter(s)
Running out of fuel
Poor compression
Defective computer

Hope this helps and just keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa.

DTC P0305 Code - Cylinder #5 Misfire DetectedA P0305 code means that the the car's computer has detected that one of the engine's cylinders is not firing properly. In this case it's cylinder #5.Symptoms may include the engine may be harder to start, the engine may stumble / stumble, and/or hesitate or other symptoms may also be present. Other tips to solve it in the previous fault code link.A code P0305 may mean that one or more of the following has happened: Faulty spark plug or wire Faulty coil (pack) Faulty oxygen sensor(s) Faulty fuel injector Burned exhaust valve Faulty catalytic converter(s) Running out of fuel Poor compression Defective computerHope this helps and just keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.Thank you for using FixYa.

• This head is torqued in three stages. Start at 1 and go to 12 each step in a row.
• 15 foot lbs.
• 44 foot lbs.
• + 130 degree all the way around as well.

Regards, Tony

• Align the marks on the timing gears before removing the belt

• Line up the balance shafts before installing the belt

• Check the alignment of the balance shafts and crankshaft before tightening the tensioner.

• Use an Allen wrench as a counter-hold when tightening the tensioner pulley.

• Pulley alignment marks for timing belt replacement.

• If you have any comments please feel free to leave them here.
• Hope this helps and thank you for using FixYa.

Regards, Tony

sometimes you can take and hit the key inward and then pull it out try this first and see what happens. use a hammer or the handle of a screw driver but not real hard. hope this unsticks it for you.

Could be fuel pump, fuel filter, air filter.

Check engine idle speed, check fuel filter, check fuel system for water ect, add dfry gas to take out water, check distributor caps and wires, check emision system , check spark plugs, check for manifold lead, check fuel injectors, and fuel control system.

check fuse/s main relay and conections

Go to your local auto zone the will tell you what is wrong and why the engine light is on >>
> Using a Code Scanner <
and the best part it is free

It's always the larger of the two.