20 Most Recent 1991 Mercury Topaz 4 Door Questions & Answers

0helpful
1answer

My ignition switch on a Mercury topaz won't start

check battery
9/10/2017 10:07:09 AM • 1991 Mercury... • Answered on Sep 10, 2017
0helpful
1answer

Fuse box location

located under the dash to left of the steering colume.
8/6/2014 3:46:59 PM • 1991 Mercury... • Answered on Aug 06, 2014
0helpful
1answer

1991 wheel bearing replace

If you are talking about the front, it is generally replaced as a assembly, wheel bearing/hub assembly, that runs about 40-60 bucks. You will likely need a puller to remove it easily, relatively simple job with a good puller.

3/18/2013 1:23:43 AM • 1991 Mercury... • Answered on Mar 18, 2013
0answers
0helpful
1answer

During the summer time it

What causes this is ussually the oxygen sensor. It works when the engine heats up and if its no good, it will run your engine lean or even shut it down. check them and replace them. They should be done every 2 years.
11/26/2012 9:12:56 PM • 1991 Mercury... • Answered on Nov 26, 2012
0helpful
1answer

My clutch wont get hard and i can shift it has a new clutch

The problem is an air problem you must have over looked something .You call the master cylinder what ? This is the one on the pedal checks for leaks on the inside of the vehicle if oil can get out air is getting in Then you say slave cylinder this is at the clutch inside the bell houseing and is the main bleeding point with a fitting to bleed the system . The olny other point is the resiverior unless the system is feed from the break system sometimes it is but not common . The springs are mechincal but the system is hydrolic so look for oil leaking and thats ware air is getting in dubble check it
3/29/2012 2:54:14 AM • 1991 Mercury... • Answered on Mar 29, 2012
0helpful
1answer

Replace water pump

For water pump replacement i suggest you to check the help link provided below.

click the link below :----

Water pump replacing procedure for all vehicles?

http://technoanswers.blogspot.com/2011/11/water-pump-replacing-procedure-for-all.html ---------

HOW TO REPLACE A WATER PUMP

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-water-pump.html

------------------ How to route Water Pump Belt for 1992 Oldsmobile ?

http://carbeltrouting.blogspot.com/2011/12/how-to-route-water-pump-belt-for-1992.html

--------- How to replace Water Pump on Car ?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-water-pump-on-acura-car.html

--------- How to Remove Water Pump?

http://technoanswers.blogspot.com/2011/12/how-to-remove-water-pump-on-toyota.html

------- Where is Water Pump located ?

http://technoanswers.blogspot.com/2011/12/where-is-water-pump-located-on-toyota.html

----------- This will help. Thanks

2/20/2012 7:21:51 AM • 1991 Mercury... • Answered on Feb 20, 2012
0helpful
1answer

Is there a fuel reset button on a 1991 mercury topaz

Yes there is one. It is on the passenger side of the front seat and it is behind the kick panel, the button is Red.
1/24/2012 9:14:42 PM • 1991 Mercury... • Answered on Jan 24, 2012
0helpful
2answers

Tires wear on the inside on both rear tires

You need to have a front end alignment done, and most likely you lower ball joints and possibly struts need replaced Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/sean_54c3a3dc48a7773c
8/24/2011 2:24:37 PM • 1991 Mercury... • Answered on Aug 24, 2011
0helpful
1answer

Rear tires wear on inside

Needs alignment, also check your shocks to be sure they are in good condition, if shocks or other part of suspension is bad, it needs to be replaced before alignment is done, otherwise, you go back to square one and will keep wearing out your tires.
8/23/2011 4:19:31 PM • 1991 Mercury... • Answered on Aug 23, 2011
0helpful
3answers

Location of thermostat

Ford Tempo/Topaz 1984-1994 Repair Guide

e1fbdf2.jpg

Fig. 1: Engine thermostat-2.0L engine



0788d3c.jpg

Fig. 2: Engine thermostat-2.3L engine


9f9f63e.jpg

Fig. 3: Engine thermostat-3.0L engine


912da81.jpg

Fig. 4:
Remove the harness from the housing


838f4f0.jpg

Fig. 5: With the retaining bolts removed, take the thermostat and housing out of the engine compartment, and place on a clean surface

55ded96.jpg

Fig. 6: Remove the thermostat from the housing. Remember the direction in which it was installed

I really hope helps with this (remember rated this help) Good luck.
5/5/2011 10:22:04 PM • 1991 Mercury... • Answered on May 05, 2011
0helpful
1answer

1991 Mercury Topaz engine stalls while

Hey check out my thread, see if we are having the same problem, sounds familiar possibly.

http://www.fixya.com/ThreadAsker.aspx?thid=7662591
1/17/2011 3:36:16 PM • 1991 Mercury... • Answered on Jan 17, 2011
Not finding what you are looking for?
1991 Mercury Topaz 4 Door Logo

62 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Mercury Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Topaz Mercury

  • Topaz Mercury

Most Popular Question

tires wear inside both rear tires

  • Cars & Trucks
Loading...