For strangeness like that you need an auto electrician rather than falling into the 'let's try replacing this' method of auto repair. Their $5,000 pro grade scan tool computer can diagnose and record TCM issues as they happen and solve anything to do with electronics, modules and the ECM / BCM / TCM.
https://www.google.com/search?q=auto+electrician+near+me
..
Hi, Seems that the SKIM (Security Key Immobilizer Module). Try locking and unlocking drivers door, sounds like security system was triggered. If unlocking and locking door does nothing locate (ECU) fuse, (Main) fuse, and (IOD) fuse. If so pull fuses turn key to on position do not start, wait 3 to 5 minutes install fuses and try starting. Please also check battery connections for clean and secure.
Hi. Thanks for your question. For assistance on any sound issuerelated to gear on Chrysler Town you can visit https://www.reliable-store.com and download the entire workshop manual which includes all the information along with the diagrams for better understanding. Good day!
Buy a cheap code reader ($20) and check your codes or go to your local parts place and some will read your codes for you for free.A blinking "check engine light" is a severe warning and the codes should be checked NOW.
Do you know about body electronic's ? BCM - body control modules , power lift gate module , serial data communication networks for the modules to talk to each other , send commands , share info, etc.... You should have taken it to a qualified repair shop. Hooking up a factory or professional type scanner to check for DTC'S - diagnostic trouble codes an view rear hatch sensor data parameters should have been done before replacing any parts that your not totally sure will fix the problem . Testing an not guessing .
Most likely the motor is going bad, but it could be the switch. If fiddling with the switch will make it work sometimes, replace the control panel. Otherwise, replace the motor.
Hello Nick, If you are hearing ANY response from the remotes... (Your radio xmitters & recvrs are cool, clean & dry)... Look elsewhere for your troubles...!! This may be as simple as clearing tracks... or more complex (actually cleaning, lubricating or replacing solenoids and motors)... Replacement interior pulls (see below) Pulling interior panels is best done with genuine FACTORY or PROFESSIONAL shop grade repair manuals... ( Big NAMES (Not internet trash))... Trim And Molding Tool Set 5 Pc Worst case manual... 2001 CHRYSLER TOWN COUNTRY 3 8L V6 Repair Manual RockAutoMore Information for DORMAN 93360Please comment me back with QUESTIOS...(I have been severely neutered by McAfee... butI will prevail... I want to help )We can do this(carnac)
over fuel from bad needle and seat , or leaking injector seals you didn't mention make model year or type of equipment so that answer is the best you get
If the coolant level is right and the water pump is working, then you probably have an air pocket in the system. Pull a vacuum on the entire cooling system and then see how it works. The epoxy patch on your radiator won't last, so start saving for a new radiator now.
Battery voltage is way low when you crank makes it sound like a machine gun. This can also be caused by a loose or corroded battery cable. Test the battery for a bad cell and look at the alternator to see if it is working correctly.
by replacing the battery the anti-theft code requirement has been activated
check the radio forums and comments on this site as there are ways to recover the code
For things wich are complicated enough and comes with guarantee only if installed by an agreed technician, I personally prefer to go to service, even if cost me a bit extra. Can be so many reasons for not working properly yor A/C that I am afraid even the old one was not the problem, since the new one is having the same symphtomps. Can be a simply fuse for A/C.
remove the fuel cap if the engine keeps running then your vent pipe for the tank is blocked or you have not fitted this back on when fitting the new tank. the vent tank has a sensor that regulates the volume of air into the take if its not connected the fuel will not flow properly.
Did you pull a vacuum on the system before charging? Disconnect the blend door actuator and turn it by hand. These aren't known for having stuck blend doors.