Top 20 1995 Acura NSX Questions & Answers

Remove the radio and recite the serial and model number to an Acura dealer to get the code.

brake light switch on the pedal under the dash needs ajusted and may be replaced.....hope it helps

Hi there, Do you mean there is water in your fuel tank?

I suspect your clutch needs overhauling.

Here are the instructions to test the braking switch and related components to locate the fault. Brake Pedal Position Switch Test 1.) Disconnect the 4P connector from the switch (A). 2.) Remove the brake pedal position switch. 3.) Check for continuity between the terminals according to the table, using a multimeter. 4.) If the continuity is not as specified, replace the brake pedal position switch and adjust the pedal height. 5.) If OK, install the brake pedal position switch and adjust the pedal height.

Question edited for clarity and make sentences.Remove the unit, remove the connectors, spray them with electrical contact cleaner and then replace them making sure they are well locked into place.Or there is a dry joint inside the unit.Start with the easy stuff first.https://www.google.com/search?q=Acura+RLX+radio+turns+off+every+time+I+hit+a+bump..

Unlikely :>D https://www.google.com/search?q=2006+Acura+MDX+navigation+system+code+for+free ..

Sure you can drive it. Only problem is the radio may have a security code if you pull the fuze you'll need the code...it should come w/ the owners manual.... if not then you gotta take out the deck and there should be a serial number behind the deck which will tell you the code for the deck. Or the dealer can help with the vin and a ID that you own the car. Best to you.

Unhook the negative post of the battery for a minute and that should reset the computer.

need to remove the door panel ---if chid lock was on would be able to open using outer handle most likely linkage or clip fail

Check for spark to the plugs and fuel to the injectors. A scanner would help to find a problem. First start by spraying a little starting fluid into the throttle body. If it starts, then check fuel pressure. You may have a bad pump or relay. If no spark, problem could be a bad sensor or bad connection to a module.

Sadly, for a vehicle of this vintage, even a locksmith would have to call the company, probably pay a fee which he would pass along, just to get the "pin" for the vehicle. Using a locksmith to do this is very likely considerably cheaper than having a dealer do such. That's my experience.regarding even a 2007 vehicle.

ck here.... https://duckduckgo.com/?t=ffab&q=+remove+the+wiring+from+the+rear+view+mirror+in+a+04+Acura+TL&atb=v159-1&ia=web

the car needs service. takes tools to diagnose no starts. lots all fuses good.? will it start with 5%(at tad) right foot depressed? on throttle. IMMO lamp glowing on the dash and ignored? immoblizer. lamp in the cluster. per the users guide (lost)>? there are up to 50 causes. check for spark?

More information please. What exactly do you mean by "smoked some"? How heavy was the smoke, was it thicker and heavier than normal? Did it have colour to it like a dense white or a blue tint? This information gives clues to the problem. The engine spinning but not starting is commonly a 'No spark' issue but if you can get it to run some of the time it could be a faulty sensor. Do you have any warning lights on the dash? It could be worth you getting it scanned with an OBD2 scanner to look for trouble codes. These give clues to any faulty sensors. If you have to pay for this service ask at 4 or 5 places as prices can be VERY different. Why do you need access to the fuses under the stereo? These are not normally a common set of fuses that cause issues. The fuse panels most commonly used in an MDX are under the hood, left side trim panel (nearest the door hinge) in the driver's footwell and in the left side trim panel in the truck.

Hi Carma archer, USA CAR? NO MODEL ACURA TOLD CL, INTEGRA, NSX, RL, SLX AND TL ??? WE CAN NOT GUESS CARS. WORST THE 6 ,MODELS IN USA ARE NOT 2.0L EVER. 2.2 lITER YES. 4 CYLINDERS. IMO if you need to ask that, then you shouldn't try. the bolts on the the STAT MAY BE M6 OR M8 HEXHEAD. TORX OR ALLEN HEX INTERNAL.KEY TYPE. ONLY LOOKING FIRST WORKS . A BUCKET TO CATCH AF50% ANTIFREEZE DRAINED HOSE CLAM TOOL. SOCKET DRIVERS FOR THE 3 KINDS OF BOLT AND FRESH AF50% AS 26 YEAR OLD IS NO GOOD AND OLD HOSES MAY/WILL BE BAD. THE VIN NUMBER TELLS WHAT CAR IT IS THE VIN#8 DIGIT THE ENGINE I'D HAVE SPARE NEW HOSE FOR THE FIRST ONE REMOVED TO THE STAT, THAT OLD HERE IS 97 MODEL CL COMING OFF 12/13MM HEADS SEEMS (HEX) THE BOLTS ARE METRIC. ALL SHOPS HAVE METRIC TOOLS, FOR SURE 12 TO 15MM ON ANY CAR FROM JAPAN.

there is none; how to reach it, to remove it and or put them back in? there are no core plugs in the 3.5L head the block. has... NONE so why ask for it? 3.5 L J35A8 (286 hp) V6 (Type-S only)\\ none but has screw plug for block heater, no freeze or core plugs here. so you are confused or listening to internet geeks? you saw leak to the ground sure. but forgot to find the source and is not a freeze plug there is NONE THERE>! none see all sides of it here, none;. https://www.ebay.com/itm/165192135142

The Transmission Control Module (TCM) on a 1998 Acura 3.0 CL is located under the center console, just in front of the shifter. To access it, you will need to remove the center console by unscrewing and prying off the cover around the shifter and then removing any screws or bolts holding the console in place. However, slow gear engagement and trouble shifting into 2nd and 3rd gears can have multiple causes, and the TCM may not necessarily be the root cause. It's best to have the vehicle diagnosed by a qualified mechanic or Acura dealership to determine the exact cause of the transmission issues.