2003 Cadillac CTS - Answered Questions & Fixed issues

On this website you find fuse box diagram and description for Cadillac CTS (2003 and 2005)


2003 Cadillac... | Answered 13 hours ago | 226 views

I have a similar problem with a 2003 cadillac cts. The water drips from the bottom area of the glove compartment. If you would stick your hand under and feel around, there is a removable panel ( two small bolts and one star screw) there , you will fell the sponge on the other side of the panel is wet. I removed this panel and ran the air conditioner and place a large mirror on the floor and shine a flash light up but did not see any water dripping.
The Driver side has a similar panel, I removed that also but saw nothing, not even the canister. But the out side pipes from the AC show the canister leads in the hood under ther driver side.
Any way I looked under the car and found the drain hose. It is located under the driver seat area. I tried fishing a coat hanger through it and it went a long way up. If you look on the side panel where the parking brake is located you will see this hose going to the top of the hood. You will need to depress the parking brake for a better view. I tried the Ac bot no condensation water came throug.
I late found a similiar hose on the passenger side. I tried to push the wire in but did not get too far.
One of these hoses drain the Sun ( moon) roof.
I then took a cap from a silicone tune ( u know the screw on tip that you cut at 45 degrees) That I inserted into the tube under car, then I insert a small funnel into the silicone cap , next with my garden ready and flowing , I force water up through the AC drain hose. Dont do too long, 5 to 7 secs is good. You will see the water come through the other drain hose. It is best to have some onlookers. Note some water might flow up to the moon roof drain and into the car so place some towel on the seat.
That works for me.
Thanks all
and good luck

2003 Cadillac... | Answered on Apr 08, 2019 | 3,556 views

If it's 4 cylinder it's 1342, if it was ok and now wont start has immobilizer got stuck??

2003 Cadillac... | Answered on Mar 04, 2018 | 16 views

Don't know how you read these codes but their is no H in back .
Factory service repair info.
DTC B3832 or B3833
Express Up operation of the front door power windows is monitored and controlled by the front door modules, the window sensors, and the 4 connecting circuits. Each front door window motor has a window sensor mounted to it. The driver door module (DDM) and the passenger front door module (PFDM) each supply battery positive voltage and ground to power their respective window sensors. Each door module communicates with its sensor via a power window high speed serial data circuit, and a power window low speed serial data circuit. The window sensor detects differences in the window motors electrical pulses to determine if there is an obstruction to the travel of the window glass. The door modules use the information generated by the sensors to disable the Express Up movement of a window, or reverse the direction of travel, in the event that a passenger, or other obstacle, has become trapped in it.
The power window low speed serial data circuit is a unique 2-way serial data link between the door module and its sensor. The actual position of the window glass, in relationship to the distance traveled by the window, is communicated via this circuit, as well as state-of-health messages and the direction in which the window is traveling.

DTC B3832 may be set and the Express Up function disabled if the vehicle or the door module has recently lost power for any reason. You should first attempt to re-initialize the Express Up function. Refer to Window Motor Programming - Express Function .
If DTC B3832 is accompanied by DTC U1714, utilize the DTC U1714 or U1716 diagnostic table before using this table. Refer to DTC U1714 or U1716 .

DTC B1420
Battery positive voltage is supplied at all times to the seat adjuster switch and the memory seat module (MSM) through the same circuit. The MSM uses this battery voltage input to determine if battery positive voltage is applied to the seat adjuster switch.
DTC B1825, B1850, B1860, B2355, B2365, or B2375
Circuit Description
The position sensor that sets this DTC is attached to the seat directional motor. It receives a 5 volt reference and low reference from the memory seat module (MSM). The sensor sends a voltage signal that varies with the movement of the seat through the signal circuit to the MSM. Then based on this voltage signal, the MSM determines the position of the seat.

Install a scan tool.
Turn ON the ignition, with the engine OFF.
With a scan tool, observe the appropriate Sensor parameter in the Memory Seat Module Sensor data list.
Does the scan tool indicate that the Sensor parameter is within the specified range?
0.25-4.75 V

Sure you can move the seat back . Connector # 3 at the MSM ,pin's S & N - lite green & tan wires . Give a ground to one an B+ to the other ,if it moves in wrong direction switch the wiring around ..

2003 Cadillac... | Answered on Jan 28, 2018 | 269 views

I have no clue what any warranty has to do with any light coming on when you first start your Cadillac. I cannot help you with your problem unless I know which light is coming on. Then, even if I knew which light was coming on, it would probably require scanning the onboard computer system in you vehicle to find out why the light is on. What would you like for me to do for you?

2003 Cadillac... | Answered on Jan 21, 2018 | 115 views

Have your dealer or a qualified Cadillac mechanic check the anti-theft system and your key. Your ECM may need to be re-flashed, but have a diagnostic scan performed to determine possible solutions.

2003 Cadillac... | Answered on Jan 19, 2018 | 47 views

Recommend taking your car to dealer or a mechanic who can perform diagnostic scan. Then report back with trouble codes for possible solutions.

2003 Cadillac... | Answered on Jan 19, 2018 | 32 views

Heat sensor on the Engine more than likely. If it gets stuck the car thinks it's still hot and won't let it re-start until it completely resets.

2003 Cadillac... | Answered on Jan 16, 2018 | 28 views

Have you checked the transmission fluid level. Hard changing or slipping can be caused by low fluid level. If it is not this, then you will need to take it to a transmission specialist to have them diagnose it.

2003 Cadillac... | Answered on Nov 22, 2017 | 69 views

pipe that come from cansiter conncted to the purge valve

2003 Cadillac... | Answered on Nov 20, 2017 | 946 views

connect it directly or by the if the relay have minous and psitive its better to check engine fuses before

2003 Cadillac... | Answered on Nov 20, 2017 | 25 views

intake air manifiold problem not open

2003 Cadillac... | Answered on Nov 20, 2017 | 183 views

have problem connection on can bus

2003 Cadillac... | Answered on Nov 20, 2017 | 692 views

this problem appier somtimes when the crank sensor stuck or have problem
try to check it by obd this kind of sensor its hall sensor that can give you date 1 0 on ( off)

2003 Cadillac... | Answered on Nov 19, 2017 | 49 views

It could just be a software issue with your EBCM. You can have it reprogrammed at the dealer. Those particular cars tend to have that issue.

I’m happy to assist further over the phone at https://www.6ya.com/expert/kim_3202917d7c587455

2003 Cadillac... | Answered on Nov 09, 2017 | 235 views

Has Transmission Manual Shift Shaft Switch Assembly. It's inside the transmission .

2003 Cadillac... | Answered on Oct 20, 2017 | 213 views

Not finding what you are looking for?
2003 Cadillac CTS Logo

1,667 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Cadillac Experts


Level 3 Expert

84543 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides