20 Most Recent
2003 Volvo V40 - Page 9 Questions & Answers
How to change 2007 Volvo S40 2.4L lower Intake manifold gasket and valve cover gasket
the service manual covers all that ,every step.
battery lug NEG - pulled first. (isolated)
step 2 ,
depressurize fuel line, not get gas in eyes.
tell the kids to not smoke or uncle Fester too.
i PULL THE FUEL PUMP FUSE OR RELAY AS ENGINE RUNS AND HEAR IT SLOWLY DIE IN SAY 1MIN OR SO,..NOW CAR IS SAFE TO WORK ON.
NOW LEARN THERE ARE TOOLS TO OPEn a line
and I have no idea what Volvo uses, but the manual will call it out. (OR GOOGLE IT TO LEARN FOR VOLVO)
some fuel lines conns have built in latches, to trip
Read IT.
seen here.
https://eautorepair.net/Marketing/Default.asp
Cooling fan removal on 2010 volvo XC60
1. Disconnect the negative battery cable.
2. Raise the vehicle and remove the plastic body panel located at the front of the engine bay and behind the front bumper.
3. Remove the upper radiator support bolts.
4. Unplug the electrical connector from the cooling fan.
5. Remove the mounting bolts for the fan.
6. Remove the fan.
7. Installation is the reverse of removal.
How do i replace the return hose #26 to the coolant overflow tank on 2004 Volvo xc90
1. Disconnect the negative (black) battery cable from the vehicle's battery. Locate the coolant tank and hose #26.
2. Remove the hose from the coolant tank by loosening the clamp and gently pulling off the hose.
3. Cut the new replacement hose to the desired length.
4. Attach the new hose to the coolant tank, ensuring that the clamp is tightened properly.
5. Reconnect the negative battery cable and check for any coolant leaks.
2010 volvo s40 trunk lid mirco switch replacement
The microswitch for the Volvo S40 trunk lid is located inside the trunk lid panel. On the left side of the trunk lid panel, you should be able to locate the access panel for the microswitch. Remove the panel to access the switch. Disconnect the electrical connector from the switch and remove the mounting screws to remove the microswitch. Install the replacement switch by tightening the mounting screws and reattaching the electrical connector. Test the switch to make sure it works correctly and then reinstall the access panel.
Location of my tcm on my Volvo xc90 awd 2.9
The Transmission Control Module (TCM) on a Volvo XC90 AWD 2.9 is located under the driver's side dash, attached to the underside of the steering column. It is mounted behind the steering wheel and can be accessed by removing the lower dashboard panel.
2010 xc60 volvo Does the throttle body have to be reset after cleaning
Yes, it is recommended to perform a throttle body adaptation or reset procedure after cleaning the throttle body on a 2010 Volvo XC60. This is because cleaning the throttle body can remove built-up carbon deposits and change the air flow through the throttle body, which can affect the engine's idle speed and performance.
To perform the adaptation or reset procedure, follow these steps:
- Reinstall the cleaned throttle body and reconnect all electrical connectors and hoses.
- Turn the ignition key to the "On" position, but do not start the engine.
- Wait for 30 seconds to allow the throttle body to initialize.
- Turn off the ignition key and wait for 10 seconds.
- Start the engine and let it idle for 10 minutes with all electrical accessories turned off.
- Turn off the engine and wait for 10 seconds.
- Restart the engine and take it for a test drive to ensure proper idle speed and performance.
If the engine still does not idle well after performing the throttle body reset procedure, there may be other issues causing the problem, such as a vacuum leak or a faulty sensor.
Volvo fl 10 valve clearance
The valve clearance specification for a Volvo FL10 truck depends on the specific engine model and year of manufacture. Generally, the valve clearance for the FL10 truck with a Volvo D10 engine should be checked and adjusted as follows:
Remove the valve cover: Remove the valve cover to access the valves.
Rotate the engine: Rotate the engine to the top dead center (TDC) position for the cylinder you want to adjust.
Check the valve clearance: Use a feeler gauge to check the clearance between the valve stem and the rocker arm. The specification for the valve clearance should be listed in the engine service manual.
Adjust the valve clearance: If the clearance is not within the specified range, adjust the clearance by loosening the lock nut on the rocker arm and turning the adjustment screw. Tighten the lock nut when the clearance is correct.
Repeat for each cylinder: Repeat the above steps for each cylinder.
Reinstall the valve cover: Once all the valve clearances have been checked and adjusted, reinstall the valve cover.
It is recommended to refer to the engine service manual for specific instructions and specifications for your particular Volvo FL10 engine.
I crashed my Volvo s80 2007 3.2 and worked on putting it back together and it won't cracked or start and I can't pull out the fob I thought it might be the shut off full switch but I can't find it?
If your 2007 Volvo S80 3.2 is not starting after being involved in an accident, there could be a number of issues that need to be addressed. Here are a few things to check:
- Ignition switch: The ignition switch is responsible for sending power to the starter motor and other electrical components. If the switch is damaged or not working properly, the engine will not start.
- Battery: After an accident, the battery may have been damaged or disconnected. Check to make sure the battery is fully charged and connected properly.
- Fuel system: The fuel system may have been damaged in the accident, preventing fuel from reaching the engine. Check the fuel pump, fuel filter, and fuel pressure to make sure they are working properly.
- Starter motor: The starter motor is responsible for turning the engine over when the key is turned. If the starter motor is damaged, the engine will not start.
- Shut-off switch: Some Volvo models have a shutoff switch that is triggered in the event of an accident to prevent the engine from starting. This switch may have been triggered and needs to be reset.
- Key fob: The key fob needs to be in the car for the car to start. If the key fob won't come out of the ignition, it may be that the key fob is jammed inside the ignition and needs to be pulled out.
It's very likely that the shutoff switch is the cause of the problem, as you suspected. You should check your car's owner manual or contact a Volvo dealership or a professional mechanic to help you locate the shut-off switch and check if it is the cause of the problem. It's also possible that the accident caused multiple issues and it's best to have the car properly inspected by a professional.
Not finding what you are looking for?