1990 Lexus LS 400 - Page 6 - Answered Questions & Fixed issues


7c528ac.gif

Thanks for using FixYa - a 4THUMBS rating is appreciated for answering your FREE question.

1990 Lexus LS... | Answered on Sep 05, 2010 | 702 views


remove the EFI fuse few seconds, located in fuse box under hood

1990 Lexus LS... | Answered on Sep 03, 2010 | 260 views


Nightmare ,
Under intake manifold.

1990 Lexus LS... | Answered on Aug 29, 2010 | 19 views


The bleeder screw is in the back next to the brake line into the caliper. Start the bleeding at the right rear, farthest from the reservoir. Then move towards the front left. Keep checking the fluid level and make sure you don't let go of the pedal with the screw loose. Get a 6 point box wrench on there , about 8mm, and a piece of hose to run the fluid into an empty can. Check it out, hope this helps.

1990 Lexus LS... | Answered on Aug 29, 2010 | 199 views


It means Electronically Controlled Transmission.

Basically in the older models there is an option to turn ECT on which allows for better acceleration as it's controlled electronically.

Hope help with this.

1990 Lexus LS... | Answered on Aug 23, 2010 | 470 views


the low side its located between autopilot actuator and windshield, passenger side firewall

1990 Lexus LS... | Answered on Aug 06, 2010 | 278 views


traction control is a separate system. If traction control or ABS is a problem they are taken out of the loop and the normal brakes still work. The master is for the brake system/ The ABS module and valve body and wheel sensors are your traction/antiskip system.

1990 Lexus LS... | Answered on Jul 24, 2010 | 210 views


Check the amount of vacuum on the distributor with a guage?? perhaps too high or leaking...

1990 Lexus LS... | Answered on Jul 21, 2010 | 316 views


open the hood and locate the big hose that comes form the radiator on the top it is under the air channel cover that goes across the top of the radiator remove it and you will see the hose in the middle of the front of the engine remove the 2 bolts and be careful not to spill alot of your coolant or if it is hot to burn yourself once you get the thermostat housing off pop the old one out and put a new o ring or gasket in there with the new one tighten it back up and put the air channel back on and re fill the coolant start it check for leaks and you are good to go if there are no leaks.

1990 Lexus LS... | Answered on Jul 18, 2010 | 190 views


open the trunk and take down the liner inside the trunk and there are some 10 or 12 mm bolts there to take the tail light assembly off the car and you can change the bulbs from there.

1990 Lexus LS... | Answered on Jul 18, 2010 | 570 views


there is a fuse box under the hood with the big relays that plug into the car right in front of the coolant over flow tank use a screw driver and loosen the two big screws and take it off and turn it over and look inside it and it will tell you which one is the relay for the air sus.

1990 Lexus LS... | Answered on Jul 18, 2010 | 74 views


To my knowlegde there is a relay a high and low pressure switch an expansion valve a compressor evaporator and condensor in an a/c system. I have'nt heard of the evp valve. if you talking about the expansion valve it starts out for about $2.00 at the parts store. try another mechanic

1990 Lexus LS... | Answered on Jul 18, 2010 | 175 views


Follow the radiator hose from where it attaches to the radiator, the bulb it is attached to contains the thermostat. put the old one in a pan of boiling water to see if it opens and closes if not replace, be sure to clean the surface that this metal bulb rests one both bottom and top and use a good sealer when re installing with a NEW gasket, take care in NOT tightening the two bolts too tight as that is light cast iron or aluminum

1990 Lexus LS... | Answered on Jul 16, 2010 | 170 views


you are joking ,right?

1990 Lexus LS... | Answered on Jul 11, 2010 | 40 views


This is best handled by a shop which specializes in AC repair. I doubt you have the proper equipment to flush, lubricate and recharge the system. It isn't as easy as it once was when you screwed a can of refrigerant to the nipple on the low pressure side of the circuit.

1990 Lexus LS... | Answered on Jun 28, 2010 | 329 views


Yes it runs the water pump,the car will over heat almost as soon as the belt breaks wile driveing down the road.Thanks for using Fixya.....Ray

1990 Lexus LS... | Answered on Jun 22, 2010 | 244 views


Check coolant level in the overflow bottle.
Have you ever had the coolant system flushed and replaced?
Is the temperature indicator light on?
Any fluid leaks?
Check those as well.

1990 Lexus LS... | Answered on Jun 13, 2010 | 85 views


its possible with a remote start system

1990 Lexus LS... | Answered on Jun 09, 2010 | 266 views


If it has r12 in it just drain it out and recharge the system with R134A.

1990 Lexus LS... | Answered on Jun 07, 2010 | 204 views


then it's probably a ground wire that isen't atached

1990 Lexus LS... | Answered on Jun 04, 2010 | 334 views

Not finding what you are looking for?
1990 Lexus LS 400 Logo

394 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

1991 Lexus LS 400
1991 Lexus LS 400

516 Questions

1994 Lexus LS 400
1994 Lexus LS 400

240 Questions

1996 Lexus LS 400
1996 Lexus LS 400

171 Questions

1995 Lexus LS 400
1995 Lexus LS 400

151 Questions

1998 Lexus LS 400
1998 Lexus LS 400

91 Questions

Top Lexus Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...