Top 20
2005 Lexus Is 300 Questions & Answers
Where is slave cylinder located on is300
i presume your asking about the clutch slave cylinder ,this will be located under the hood at the bulkhead end of engine compartment ,there will be a small fluid resovoir sitting on top of the actual hydraulic slave cylinder , the clutch fluid resorvoir is smaller , and usually not opaque, than the brake fluid resorvoir, which are usually next to each other , incidentally the brake also has a slave, or more usually known as the master , cylinder
Lexus is300 wont revv past 3000rpms has code p0103
P0103 OBD-II - Mass Air Flow (MAF) Circuit High Input
This DTC means that there is a problem with the Mass Air Flow High (MAF) sensor or circuit. A more technical description would be that the MAF circuit had higher than expected voltage (air flow). Other MAF sensor circuit DTC trouble codes are P0100, P0101, P0102, and P0104.
A code P0103 may mean that one or more of the following has happened:
- The MAF may be disconnected, or a wiring connection may be bad
- The MAF sensor may be damaged
- The vehicle computer may be faulty (very rare)
Feel free to contact us in this DTC P0103 code link, if you need additional details.
Hope this helps; also keep in mind that your feedback is important and I'll appreciate
your time and consideration if you leave some testimonial comment about
this answer.
Thank you for using Fixya, and have a nice day.
How to install front & rear side marker lights
Accessing a Lexus Side Marker LightIt's actually not as difficult as it seems.
Look in the fender liner area (where the wheel wheel is) and you will see the screws that hold the liner in place.
Once you remove the bottom screws (or be it the screws that hold the edges of the fender liner), you can carefully pull it back a bit to expose the bulb and socket. To remove the socket turn it counter clockwise until you can pull it out. To reinstall the socket turn it clockwise until it locks in place
Carefully remove the bulb from the socket and replace with same type. To remove the bulb pull it straight out. Push the new bulb straight in. The bulb is a 194 5w bulb.
Note: most of the time the reason the bulbs are burning out in the bumper is due to water getting in behind the lens and not being able to drain.
What I have done is use a Dremmel tool to carfully drill a very small hole along the bottom of the lens to allow the water to drain. Another option is if you have clear silicone you can suirt some around the outside of the lens. This will prevent water from getting in. However, if there is already water in the lens you will have to drain the water first. To drain the water use a ratchet wrench and unscrew the nut that holds the lens to the bumper.
In severe cases of corroded sockets you might have to replace the socket where the bulb goes into.
The car will not start
Car
not starting or turning over indicates towards multiple possibilities. It can
be issue with battery or weak battery. But if battery checks out ok, then it
can be starter issue or faulty alternator or problem with low fuel pressure or
no spark at spark plugs due to dirty spark plugs or faulty ignition coil or
injectors getting cracked or dirty and needs to be cleaned.
To
confirm the problem, the basic troubleshooting is required.
From
start to end troubleshooting these problems I suggest you
to check the help link below and follow its procedure: -----
Mostly all types
of car no start problems are discussed here with solutions:---
CAR NO START: ENGINE NOT TURNING
OVER:
http://alltypesofpartsreplacing.blogspot.com/2012/11/car-no-start-engine-not-turning-over.html---------These will help.Thanks.
2001 lexus is300 when you
Terry, thanks for choosing FixYa and welcome. You may have a weak alternator killing the battery, Make sure you test it. If it checks out, You may have a bad connection in the battery charging area. Check the terminals and post. Check your wire that leaves the battery and goes to the alternator.
Hi, I just bought a
why don't you try ebay, or doing a google search, or going to the manufacturer's website and clicking around in the customer service or support area.
Half of the lights are
the lights burned out try taking it apart and taping on it might just be loose but
it just might be shot. u will need to buy a new panel or get on a junk yard not hard to replace
Abs, brake won't go off,
The ABS system and TRAC system are very similar. Signals from the speed sensors in the wheel hubs and one on the output shaft of the transmission are checked against each other. If when you apply the brake a wheel is detected as running much slower than the others brake fluid is relieved from this wheel to stop it skidding. Likewise when you accelerate the speed sensors detect a wheel speeding up faster than the rest and the brake is applied to it to gain traction control. So you can see that the speed sensor operation and their signals are central to both ABS and TRAC. If you have a problem with one then you invariably have a problem with the other. You need to check that the speed sensors to the wheel hubs are intact, that the connections are good and that the wiring has continuity. Also check the speed sensor on the side of the output shaft on the transmission casing, the connection and continuity. If any part is loose this will be enough to upset the complete system.
My husband passed away on
- You are being charged each month becuase you or your husband took out a monthly subscription to our service, this monthly fee allows you to ask unlimited repair questions for one monthly fee. If you wish to cancel this monthly subscription simply send an email to Fixya.com at this email address:
[email protected]
- Tell them to cancel the monthly subscription to our service.
- I can
My 2002 lexus Is300 is
PLS DO A COMPRESION TEST THEN YOU WILL KNOW IF YOU NEED TO REPLACE YOUR PISTONRINGS OR REDUE THE VALVE SEALS AGAIN
Tail lights are out but
Check the bulbs, If one burns out it sometimes breaks the current flow and both stop working, Raz
Yes I still need help.
What area do you need help in I am sorry i only see " Yes I still need help. I have a mobile mechanic coming over at one oclock. I will tell him your solution. I had the alternator and starter checked last week. Do I need to replace the wires to the battery. If so is there any special part or tool the mechanic needs or is there any thing in particular he needs to know in order to replace it?"
I would love to help give me the area in need of repair and the specifics. Thanks, Lee Davidian
Hi, I have IS 300
Check the voltage of the battery first. If you are under 11 volts you have a charging issue. Most likely though, if your lights are working at full power it is your starter.
Turbo
let me know if you want new or used and where you are located i find car parts as a profession, especially hard to find stuff
Not finding what you are looking for?