2003 Audi A6 - Answered Questions & Fixed issues
How to adjust headlight alignment on Audi A6 2003
The adjustment screws/nuts should be located either on the top of the headlamp assembly,
behind the headlamp assembly, or near the frame rail by the radiator
support.
You will have vertical adjustment screws for each independent beam
(separate highs and separate lows, but will be same screw if highs and
lows are the same bulb). You may also have additional horizontal
adjustment screws as well
Park
your car on a level ground 30 feet from a wall and measure the height
from the ground to the bulb and mark on a wall (do this for highs beams
and low beams if the bulbs are separate, if highs and lows are the same
bulb, only do it for the lows)
For Low Beams: If the headlights read VOR, then
aim the brightest part or cutoff part just below the mark on the wall.
If it says VOL or nothing, aim them 2 inches below the mark on the wall.
For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.
12/19/2017 10:00:21 PM •
2003 Audi A6
•
Answered
on Dec 19, 2017
•
3,928 views
Starter Fluid in a 2003 Audi?????
Not sure if there are carbs on car or if it is direct injection. If carbs spray into float chamber(s) if injction I think you will have to spray into cylinders via holes for spark plugs. Pleae note have never used starter fluid on direc t injection my self so I am really not sure if that will work. I assume that you have checked that fuel is getting to engine. Hope this helps.
9/18/2017 12:37:21 PM •
2003 Audi A6
•
Answered
on Sep 18, 2017
•
369 views
Audi A6 air con always blow very hot air coming from engine with bad smell
The smell is probably related to the catalic converter when a cat goes bad it creates a smell similar to rotten eggs. You might need to replace the catalic converter. This will improve gas mileage and performance. The hot air blowing from the AC is probably a low charge on the Freon.
6/1/2017 1:57:30 PM •
2003 Audi A6
•
Answered
on Jun 01, 2017
•
291 views
How do i top up my auto transmission on audi a6 2006
The German manufacturers came up with a great new idea that many others have now copied and that is to eliminate the under bonnet filler tube and dip stick. Some of the German manufacturers have decided to eliminate engine oil dip sticks as well. These people are just so innovative.
Thus you have to use the correct filling procedure as laid down by the manufacturer which involves filling the auto transmission from under the vehicle by removing the filler plug on the side of the auto unit and pumping in the fluid. It used to be so much easier.
Obviously this is best done on a lift/hoist and the vehicle must be level.
Here is some info on the Audi A6 auto trans you may find of use..................
Audi A6 Transmission Fluid Filter Change Kit Audi A6 ATF 6spd
-----------------------------------------------------------------------------------------
1/8/2016 10:22:23 AM •
2003 Audi A6
•
Answered
on Jan 08, 2016
•
241 views
Program a remote key for 03 A6
I have an A4 and did this to re-program my key:
1. used the key to start the car...then turned it off
2. put the key in the driver door (door closed)
3. pressed the lock button on the key fob once
4. turned the key to lock the door.
This is basically the steps in the owners manual, but the car must be started with the key first, and the key must be in the door lock before pressing the lock button.
3/22/2015 3:04:13 PM •
2003 Audi A6
•
Answered
on Mar 22, 2015
•
8,604 views
How to change front struts on 2003 Audi a6
You would be better off to pay $16.00 for a haynes repair manual for that car, it gives a step by step procedure, It would take a lot to tell you on here. If you are going to change the strut springs to the new ones, you need a spring compressor, and if you don't know what your doing and be very careful, and the spring slips and hits you, you will be severelly injured.
1/23/2015 9:49:11 AM •
2003 Audi A6
•
Answered
on Jan 23, 2015
•
705 views
Not finding what you are looking for?