20 Most Recent 2002 Audi TT - Page 4 Questions & Answers

There is likely an eccentric bolt on the lower contorl arm. The one on the arm closest to the bottom center of the wheel hub is the camber adjustment, the other eccentric is the toe adjustment. You really should have it aligned with a computerized alignment machine. Changing the rear camber changes the rear toe and vise versa. It would be nearly impossible to get both within an acceptable range without the proper equipment. You can crudely measure rear toe using a tape measure but you won't know what the thrust angle is and that could cause some serious alignment issues.

IMPORTANT NOTE:
You must have the security anti-theft code for your Audi Concert radio from the car manufacturer, or from an Audi dealer!

You can find the radio code at: http://www.radio-code.co.uk/

The sequence of programming for a 2002 Audi TT Concert radio is:
1. Simultaneously push "SCAN" and "RDS" keys until on the screen will appear "1000" displayed.
2. Release keys. No more push on "SCAN" and "RDS" keys because otherwise number "1000" will be considered as first safe code attempt.
For example: we have the security code "5079". Then:
3. By the no.# 1 key you will set up the first safe code digit. Push 5 times on the no.# 1 button. The "5" number will be setted.
4. By the no.# 2 key you will set up the second safe code digit. Push 10 times on the no.# 2 button. The "0" number will be setted.
5. By the no.# 3 key you will set up the third safe code digit. Push 7 times on the no.# 3 button. The "7" number will be setted.
6. By the no.# 4 key you will set up the four-th safe code digit. Push 9 times on the no.# 4 button. The "9" number will be setted.
7. Then simultaneously push again "SCAN" and "RDS" keys to confirm this safe code. On the screen will be displayed "SAFE" notice. Release keys! For few seconds a radio frequence will be displayed.
The radio is now ready to use!

Hi, are the headlamps Zenon? If they are you will need to take the car to a dealer. If they are normal halogen lamps then you can adjust them with a 6mm hex key. If you look vertically downwards at the rear of the lamp unit you'll see the adjuster about halfway down facing up at you. simply turn with the hex key until you reach the required adjustment.
Hope that helps Matt..

go back to were you had the sensor replaced and have them repair the problem this should have been working properly before it left the shop.it could even be a bad sensor.

don't get a new top, take your car to an auto upholstery shop, they can fix that for you ,

recommend checking the position arms located below the rear quarter windows.

Thats the theft deterent....If you don't have the pass code written down, you can get it at the car dealer.

Some of them charge a $75 fee

Hi,

If you are referring to the "Inside" Mirror:

This is a little hard to put together
Be sure you have the Retaning spriing on (sometimes it gets lost)
Put parts together & turn Mirror bracket to fit in snu, then turn bracket

You could download the complete procedure from :-

http://www.mediafire.com/?c4tjbtxcwa7ltve


You need to have acrobat reader to view the file.

Let me know,if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

No not at all. Be happy thats the only issue!

i have audi tt 2000.when i was driving on highway today my car stop suddenly and EPC light was on,also check engine light was on..what s the problem on my car?

Here are a couple of resources that have dealt with similar problems as yours. I hope they help.

Audi Forum Solution 1

Audi Forum Solution 2 This one scroll down most of the page to see a simple diagnostic test you can do in a parking lot.
Audi Forum Solution 3 Maybe your best solution here.

There are some easy solutions but some that require replacement of parts. But you should feel confident on what parts need replacing after reading those three solutions. It sounds like your Haldex control unit is locking up when it shouldnt be. Appears to be a common problem.

Good Luck

IMPORTANT NOTE:
You must have the security anti-theft code for your Audi radio from the car manufacturer, or from an Audi dealer!

Also you can find the radio code at: http://www.radio-code.co.uk/

The sequence of programming for Audi radio is:
1. Push simultaneous "SCAN" and "RDS" keys until on the screen will appear "1000" displayed.
2. Release keys. No more push on "SCAN" and "RDS" keys because otherwise number "1000" will be considered as first safe code attempt.
For example: we have the security code "5079". Then:
3. By the no.# 1 key you will set up the first safe code digit. Push 5 times on the no.# 1 button. The "5" number will be setted.
4. By the no.# 2 key you will set up the second safe code digit. Push 10 times on the no.# 2 button. The "0" number will be setted.
5. By the no.# 3 key you will set up the third safe code digit. Push 7 times on the no.# 3 button. The "7" number will be setted.
6. By the no.# 4 key you will set up the four-th safe code digit. Push 9 times on the no.# 4 button. The "9" number will be setted.
7. Then push again simultaneous "SCAN" and "RDS" keys for confirm this safe code. On the screen will be displayed "SAFE" notice. Release keys! For few seconds a radio frequence will be displayed. The radio is now ready for use!