20 Most Recent 2002 Audi A6 - Page 7 Questions & Answers

when stationary their is no air flow through the radiator so temperature will rise and the cooling fan comes on ,now as for it not going off then this could be a sensor ,relay or the computer as the sensor tells the temperature to the computer which turns the fan on and off ,now on these cars the fan will stay on for up to 5 mins after turning the engine off so if after this time it hasnt gone off then consult the dealer as you have bought a asian market software vehicle so it will not respond to a code reader to locate any faults just like the europeon version but the american version can be read with a code reader .

windshield washer reservoir has a crack in it or look for leaking washer reservoir hose leaking fluid.

For Audi A6 the fuse box is located on the left side of dashboard behind a plastic cover (for left hand steering wheel vehicle). On inner face of the plastic cover you will find the fuse diagram.
The fuse for the radio is no.# 37 fuse: F37 (20A - yellow colour). See picture below:





There is a second fuse on the back of the radio, (10A - red colour), but you have to pull the unit to check & change it. This is only course of action. You need special Audi radio extracting tools, (two radio keys).

IMPORTANT NOTE: You must have the security anti-theft code for yours Audi Concert radio from the car manufacturer! For Audi Concert the sequence of programming is:
1. Push simultaneous "SCAN" and "RDS" keys until on the screen will appear "1000" displayed.
2. Release keys. No more push on "SCAN" and "RDS" keys because otherwise number "1000" will be considered as first safe code attempt.
3. By the #1 key you will set up the first safe code digit.
4. By the #2 key you will set up the second safe code digit. 5. By the #3 key you will set up the third safe code digit.
6. By the #4 key you will set up the four-th safe code digit.
7. Then push again simultaneous "SCAN" and "RDS" keys for confirm this safe code. On the screen will be displayed "SAFE" notice. Release keys! For few seconds a radio frequence will be displayed. The radio is now ready for use!

it depends on year of car and make of RADIOHERE IS THE SETTINGS FOR A 2002 AUDI A6 Quattro V6 2.7L Turbo (APB) engine code
For the Audi Concert Radio
YOU STILL NEED YOUR RADIO CODE TO ENTER THIS!!!!!!!!!!!! tell me if this work for you
Entering Anti-theft Code

The following is the procedure to re-activate the radio if the display shows "SAFE". It is important that the procedure be followed in the correct order.

1. Turn on radio. The radio display shows "SAFE".
2. Press the FM2 and RDS buttons simultaneously and hold until "1000" shows on the display. Release the buttons. Do NOT press these buttons again, otherwise the radio will consider "1000" to be the code.
3. Use Preset buttons 1 ... 4 to enter the four-digit code number from your radio card. Preset button 1 corresponds to the first digit, Preset button 2 corresponds to the second digit, etc. Each press of the button increments the number by 1.
4. Once the code shown on the display is correct, press the FM2 and RDS buttons simultaneously and hold until the word "SAFE" appears in the display, then release the buttons.
5. The radio should unlock and be usable shortly afterwards.
6. If an incorrect code is entered, the word "SAFE" appears, first flashing and then continuously. You can repeat the above steps to unlock the radio once more, the number of attempts will be shown in the display. If an incorrect code is entered again, you radio will be locked for about one hour. After one hour - the radio must stay on and the key must remain in the ignition lock - if the display goes out, the you can repeat the above procedure to unlock again. The cycle - two attempts, one hour lock-up - still applies.
7. If you lose your radio code, contact your Audi dealer.

Note: Some European market Concert radios have a TP button instead of the FM2 button, so the description above with those units would require pressing the TP and the RDS buttons simultaneously.

it can be the switch or a broken cable.

Hi your car got a speed warning system in the dash you need to reset it,check on your steering wheel or wiper and inticator levers for buttons for dash menu some models have a reset button also.hope this helps.

it is true, if not off by 100 miles return to the dealer that told you that

Hello
This cars engine is controlled electronically by a computer called the PCM, so whenever you experience a problem like this you MUST have the electronic system tested for fault codes, this is called an "OBD2" fault code test. To try and guess would cost allot of money and most likely not fix what is really wrong. Have the test run and then a trained techincian will look at the results of the fault code testing and he or she will decide what may be creating your problem of the engine hesitation when you press the gas pedal.

Bring your car to an auto parts store. The will plug a box in to see what error codes are causing the check engine light. Look up the code and fix as needed, the auto parts store will help you out, usually for free.

When the battery was removed the codes are reset and so it will be best to check your manual or the dealership database as this is easily available with them.
If not check if the following link gives some tips:

http://www.radio-code.com/

http://www.floodle.net/extra/ebayinfo/car_radio_decode.html