20 Most Recent 2003 Chrysler Crossfire Questions & Answers

sounds like worn rubber parts. Shoot some liquid lube on all the rubber parts focusing on where the rubber meets the steel part.

YOU HAVE TO GO TO THE CHRYSLER DEALERSHIP TO GET ONE.

this noise is caused by defective/out of adjustment rear end ring and pinion gears, this may be due to pinion depth or backlash adjustment, but once the noise starts the only way to correct it is to replace the gear set, if the noise is only slight then it is a watse of money to repair it, the cost of a new gear set plus labor to install them is over $1000.000

P0410 is the error code for Secondary Air Injection System Malfunction
The secondary air injection pump pumps air into the exhaust to help heat the catalytic converter at cold start. This lowers the emissions at an otherwise high emission time.
A malfunction means that computer has registered either a pump failure (common on some models), fuse blown, or improper catalytic converter function.
Check your fuses. Whether you find a bad fuse or not have the codes reset. Some auto Zones can read and reset the codes. If the error comes back you may want to consider having the exhaust system checked.Problems with the catalytic converter\converters can have a large impact on your MPG.

70% of engine rattles in new cars are of because the engine has very minimum oil, you'll find if it has the correct amount of oil in it it will not rattle, cams dont tend to rattle, and newer cars dont use tappets now :) there hydraulic lifters.

if it does rattle, and its annoying you more than anything, and you just want to stop the rattle and not botherd about finding the actual problem them simply put thicker oil in.

but im sure you will find if it doesnt have enough oil in the car, and you fill it to maximum on the dip stick, it will stop the rattle.

How to Set Clocks in a Chrysler

1. Insert the key in the ignition and turn it to the "Accessories" setting. ...
2. Press the "Set" button on the far right of the radio.
3. Push the "Sel" button once.
4. Press the "Tuning" button up or down to change the hour.
5. Push the "Sel" button once again.

More items...

How to Set Clocks in a Chrysler - It Still Runs

https://itstillruns.com > set-clocks-chrysler-6975088 and here is your manual

CHRYSLER CROSSFIRE OWNER'S MANUAL Pdf Download

https://www.manualslib.com > ... > Crossfire View and Download Chrysler Crossfire owner's manual online. 2008. Crossfire automobile pdf manual download. Also for: 2008 crossfire.

Make sure the brake fuse is ok. Without power to the switch the shifter will not shift out of park. Check your owners manual to find the emergency release button. Then check to see if it will start in N. You could have a shifter cable problem. In that case disconnect the linkage from the transmission and manually shift the transmission into the N position. Make sure that the e brake is set so that if it starts to roll you will be safe

you found the right place right time buddy.. i know a lot of websites for repairs and manuals that can really help u..

Replace the leaking piston,all the best.

code p 0101 refers to mass air flow (MAF) sensor/volume Volume air flow (VAF) sensor---range /performance problem====causes --intake leak/blockage--MAF/VAF sensor code p 0151 refers to heated oxygen sensor(HO2S) 1 bank 2--low voltage === causes --exhaust leak--wiring short to ground --HO2S--ECM for the first code , while sometimes cleaning with the correct solvent cleaner gets results, repeat problems will require a new unit as for the second code , the exhaust leak can be in the braided flex joint at the exhaust manifold The HO2S is the sensor in the exhaust manifold before the cat converter as for the last comment , find your self an accredited service center that respects their customers

Sounds like oil or coolant in the piston makes engine run rough until hot enough to evaporate. Then as engine cools the coolant seeps through the head again.Take out spark plugs have a look if oily or gunky from coolant if so need new head gasket

Don't forget to resynch the key with the ECU. Should be some info online on how to do it for your vehicle. Typically, you insert the key and then press the open doors button or hold both buttons down simultaneously.

15w40

You may have a blown head gasket.

try here:

http://www.scribd.com/doc/34216111/2004-Chrysler-Crossfire-Owners-Manual

between $800 to $1500 deepend how bad damage to the head.machine shop has the final answer.

400?p400?p0400?which one?