20 Most Recent
2001 Mercury Sable - Page 3 Questions & Answers
Thermastat location
Thermostat is on the top of engine where the hose from the radiator goes into the top of the engine. Follow the hose from the top of the radiator to where it enters the engine and there should be a hose mount with two or three bolts in it. The thermostat is inside the hose mount. Be careful you do not tighten these bolts to tight as these bolts will break. I did and had to drill the bolt out and use an easy out to repair it. It's frustrating when that happens.
Will not start, flooded
Press the accelerator pedal to the floor and keep it there! Now turn over the vehicle, it will try to start and eventually will fire up, when that happens release the accelerator pedal and it should be all good!
Thermsastat location
Most thermostats are located where the top radiator hose joins the engine, your thermostat may in the bottom radiator hose
How do I replace a serpentine belt bypassing the air conditioner ... I am not using the air conditioner pulley at all.
Odds are you can't. The ac compressor is mounted in the belt routing so it would need the pulley to keep the belt tight.
You can get a used compressor from a salvage yard and mount it in place of your old part if necessary. It will allow the belt to run even if it has no freon in the system.
There are a few vehicles that a replacement dummy pulley was designed for, but I am not aware of one for your vehicle. Usually if you try to run the belt without the compressor pulley, it will rub against something or not allow the belt to run in the right direction.
Theft light
That is normal, they all do this. it won't drain the battery.
How do I remove the lock lug on a 2001 mercury sable
You need the key.
If you have lost the lug key, most tire service centers have methods to remove them, but they usually destroy them in the process.
On the Mercury Sable, the key was originally clipped to the lug wrench but was also sometimes stored in the glove compartment.
Check engine light with codes
P0171 & P0174 indicate Lean burning on banks 1 and 2. The most common cause is a dirty or defective MAF (Mass Air Flow) sensor. Other causes are bad fuel filters or a broken vacuum line.
I have a 2001 mercury sable wagon when i open the door the light comes on but goes off and beeps when the door is fully opened
Lamps, Courtesy
The interior courtesy lamps are controlled by the generic electronic module (GEM) and are activated by the interior lamp relay. The interior lamp relay coil is grounded by the GEM when:
- a door is opened.
- illuminated entry is requested from remote anti-theft personality module.
The courtesy lamps will turn off if:
- ignition switch is turned to RUN.
- illuminated entry off request is received from remote anti-theft personality module or after 25-seconds.
-
- VISUAL INSPECTION CHART
-
-
-
-
Electrical
-
-
-
-
- Damaged lamps.
- Damaged switches.
- Stuck switches.
- Open fuses.
- Fuse junction panel fuse:
- Fuse 12 (5A).
- Open bulbs.
- Loose connectors.
- Corroded connectors.
-
If the inspection reveals an obvious concern that is readily serviced, correct the concern before continuing with Inspection and Verification.
-
If a concern remains after the inspection, connect Rotunda New Generation Star (NGS) tester 007-00500 or equivalent to the data link connector (DLC) located beneath the instrument panel to perform the Data Link Diagnostics Test. If the NGS responds with NO RESPONSE/NOT EQUIPPED for the Generic Electronic Module (GEM), GO to Pinpoint Test AD . If the Data Link Diagnostic test is passed for the Generic Electronic Module (GEM), retrieve continuous DTCs and execute self test diagnostics for the GEM.
-
If self test is passed and no DTCs are retrieved, go to the Symptom Chart to continue diagnostics.
-
If DTCs are retrieved, go to the Generic Electronic Module (GEM) Diagnostic Trouble Code (DTC) Index to continue diagnostics.
-
If the Generic Electronic Module (GEM) cannot be accessed by the NGS tester, go to Pinpoint Test AD .
Rotunda Service Bay Diagnostic System (SBDS®) 001-00001 may also be used to diagnose this system.
You mite check I/P Fuse Panel relay #37 interior lamp relay !
You mite
How many miles do I need to drive to complete the drive cycle
hi
generally the catalic converter get oily especially if the car is used
around the town the best thing to do from past experience is to drive the car down the motorway at 60mph. for good 3/4 hour at high revs
third gear if 4 gear motor you get the meaning this way you burn the oil
out because lots more heat is crated once this is done youshould pass the emission. happy driving
Turn igintion switch, engine won't start
Has anyone checked to see if you have power at the starter when the key switch is in the start position ?Could be several things including the battery, cables, starter, neutral safety switch, or key switch.
Not finding what you are looking for?