Does the pcm or ecm have a skim module secret code, if a 2002 jeep wrangler did not have the theft module installed at the factory,If not how does the dealership get a code to program the Ign. immobil
great question, wana Read the shop manual for free, ?it answers all this, its a rolling encrypted secret code.bad ideasays it all, YOU DID.now the system sees you hacking,and bricks it.there is only 1 fix. dealer time. or a shop with same tools.they must be all married or they self brickits also law here in use, DOT bs, rules.not jeeps fault < GOV BS.page 8e-1 , on, read. in jeep SM.When a PCM (JTEC) and the SKIM are replacedat the same time, perform the following steps inorder:(1) Program the new PCM (JTEC).(2) Program the new SKIM.(3) Replace all ignition keys and program them tothe new SKIM.PROGRAMMING THE PCM (JTEC)The SKIS Secret Key is an ID code that is uniqueto each SKIM. This code is programmed and storedin the SKIM, the PCM, and the ignition key transponderchip(s). When replacing the PCM, it is necessaryto program the secret key into the new PCMusing the DRBIIIt scan tool. Perform the followingsteps to program the secret key into the PCM.(1) Turn the ignition switch to the On position(transmission in Park/Neutral).(2) Use the DRBIIIt and select THEFT ALARM,SKIM, then MISCELLANEOUS.(3) Select PCM REPLACED (GAS ENGINE).(4) Enter secured access mode by entering thevehicle four-digit PIN.(5) Select ENTER to update PCM VIN.NOTE: If three attempts are made to enter securedaccess mode using an incorrect PIN, securedaccess mode will be locked out for one hour. Toexit this lockout mode, turn the ignition switch tothe ON position for one hour, then enter the correctPIN. (Ensure all accessories are turned off. Alsomonitor the battery state and connect a batterycharger if necessary).(6) Press ENTER to transfer the secret key (theSKIM will send the secret key to the PCM).(7) Press PAGE BACK to get to the Select Systemmenu and select ENGINE, MISCELLANEOUS, andSRI MEMORY CHECK.(8) The DRBIIIt will ask, “Is odometer readingbetween XX and XX?” Select the YES or NO buttonon the DRBIIIt. If NO is selected, the DRBIIIt willread, “Enter Odometer Reading (From I.P. odometer)”.Enter the odometer reading from the instrumentcluster and press ENTER.PROGRAMMING THE SKIM(1) Turn the ignition switch to the On position(transmission in Park/Neutral).(2) Use the DRBIIIt and select THEFT ALARM,SKIM, then MISCELLANEOUS.(3) Select PCM REPLACED (GAS ENGINE).(4) Program the vehicle four-digit PIN into SKIM.(5) Select COUNTRY CODE and enter the correctcountry.NOTE: Be sure to enter the correct country code. Ifthe incorrect country code is programmed intoSKIM, it cannot be changed and the SKIM must bereplaced.(6) Select YES to update VIN (the SKIM will learnthe VIN from the PCM).(7) Press ENTER to transfer the secret key (thePCM will send the secret key to the SKIM).(8) Program ignition keys to the SKIM.NOTE: If the PCM and the SKIM are replaced at thesame time, all vehicle ignition keys will need to bereplaced and programmed to the new SKIM.PROGRAMMING IGNITION KEYS TO THE SKIM(1) Turn the ignition switch to the On position(transmission in Park/Neutral).(2) Use the DRBIIIt and select THEFT ALARM,SKIM, then MISCELLANEOUS.(3) Select PROGRAM IGNITION KEY’S.(4) Enter secured access mode by entering thevehicle four-digit PIN.NOTE: A maximum of eight keys can be learned toeach SKIM. Once a key is learned to a SKIM it (thekey) cannot be transferred to another vehicle.(5) Obtain ignition keys to be programmed fromthe customer (8 keys maximum).(6) Using the DRBIIIt, erase all ignition keys byselecting MISCELLANEOUS, and ERASE ALL CURRENTIGN. KEYS.(7) Program all of the ignition keys.If ignition key programming is unsuccessful, theDRBIIIt will display one of the following messages:² Programming Not Attempted - The DRBIIItattempts to read the programmed key status andthere are no keys programmed into SKIM memory.² Programming Key Failed (Possible UsedKey From Wrong Vehicle) - SKIM is unable to programan ignition key transponder due to one of thefollowing:² The ignition key transponder is faulty.² The ignition key transponder is or has beenalready programmed to another vehicle.² 8 Keys Already Learned, Programming NotDone - The SKIM transponder ID memory is full.² Learned Key In Ignition - The ID for the ignitionkey transponder currently in the ignition lockcylinder is already programmed in SKIM memory.end quote.
3/9/2017 1:42:05 PM •
2002 Jeep...
•
2,644 views • 0 helpful votes