20 Most Recent 2000 Ford Ranger SuperCab Questions & Answers


Sometimes an air bubble - just before the injectors cause this problem. Loosen the fuel line there and crank the motor. Fuel pressure should force the air out and then fuel will squirk out. Turn key off and tighten up the line. Hope this is it. Other diesel fuel start tips are listed below that will help. http://www.auto-tune-up-and-repair-options.com/diesel-additives.html

2000 Ford Ranger... | Answered on Aug 29, 2019


hot wire from the battery to the push button and another wire from the push button to the starter side of the solenoid should do it, hope this helps

2000 Ford Ranger... | Answered on Apr 28, 2019


do a compression test,as the intake manifold,like alot of fords is no good.

2000 Ford Ranger... | Answered on Oct 03, 2018


Fuel Pump relay switch is in the main box usually located on the drivers side Fender in a black box. According to the owner's manual in the power distribution box in the engine
compartment (Ford recommends disconnecting your battery)
Relay # 5 is the fuel pump relay , and also in the PD BOX is a 20 amp mini-fuse
for the fuel pump relay + RAP module in location # 9


( P.S. - don't forget your fuel pump inertia switch , in the right front passenger area ,
by the right front kick panel )Sometimes this gets kicked by passenger or if the car is bummed hard it could set this item to shut down fuel system. Best of Luck

2000 Ford Ranger... | Answered on Sep 30, 2018


That would indicate a break in the vacuum line or a vacuum line disconnected under the hood.

2000 Ford Ranger... | Answered on Apr 28, 2018


There's this website www.reliable-store.com
They have books on ALL vehicles.
it covers
wiring diagrams, electrical diagrams,
fuse diagram, torque specs, PCV, error codes, fault codes, service info, repair info, parts info, owner's/service/repair/parts/maintenance manuals etc everything totally..
I have 1987 toyota 4runner model and I keep servicing and when needed repair it on my own. worth it !!!

2000 Ford Ranger... | Answered on Mar 18, 2018


Sounds like the computor has gone into limp mode. Have you heard any strange noises coming from under the hood lately ?

2000 Ford Ranger... | Answered on Feb 03, 2018


You probably need to check those fuses too. You may have accidentally touched something else and blew more fuses. Usually there's a plastic tool on the back side of your fuse door to remove them safely with

2000 Ford Ranger... | Answered on Feb 02, 2018


Ford ranger died while driving, wont start. Hell - YouTube

? 1:43
www.youtube.com/watch?v=vvcq14hxUBw
Oct 17, 2013 - Uploaded by Pheonix_RessurectedSLT
Ford ranger died while driving, wont start. ... 1996 Ford RangerStarting Problem - one click, then nothing ...

2000 Ford Ranger... | Answered on Jan 16, 2018


CEL comes on when 1 or more sensors are "out of normal" range. Autozone or Advanced auto parts will scan and tell you the code for free in my area. I bought a $20 OBD 2 scanner from tractor depot. It's cheap but works, and the book gives description of codes.

2000 Ford Ranger... | Answered on Jan 04, 2018


It is the slave cylinder there is a missing piece in the lock position put it back in again and try to turn the hose and it shoild lock and stay there

2000 Ford Ranger... | Answered on Nov 20, 2017


With door unlocked put key in the ignition. Cycle on and off position with key 8 times without turning the truck on within 10 seconds. Door locks should lock and unlock indicating in programming mode. Press any key on your fob. Should be programmed.

2000 Ford Ranger... | Answered on Sep 18, 2017


NO START ??????? When you turn the key to the start position , nothing happens ? Or the engine spins an doesn't start an run ?

2000 Ford Ranger... | Answered on Jul 19, 2017


That is the ignition module associated with the dist. if so equipped. If no distributor, cold be electronic spark block fro spark distribution.

2000 Ford Ranger... | Answered on May 15, 2017


The best thing would be to have transmission control module - ( computer ) checked for DTC'S - diagnostic trouble codes . The flashing O/D light is trying to tell you that . The transmission is in limp home mode . A sensor or shift solenoid is most likely the problem . Your transmission is electronically controlled , has sensors , shift solenoids , an a computer that controls it all , plus electrical signals (inputs) from the engine computer .

2000 Ford Ranger... | Answered on May 07, 2017


code p 1151 refers to the heated oxygen sensor(HO2S), bank 2 running lean===causes --intake /exhaust leak/s,-- HO2S sensor bank 2 ---wiring ---ECM
replace the heated oxygen sensor ( in the exhaust manifold before the cat converter)using the correct tube spanner to avoid damage to the sensor wires
the problem of apparent in and out of drive indicates a wiring problem to the transmission in either the torque converter clutch servo/ solenoid or TCM

2000 Ford Ranger... | Answered on Apr 20, 2017


Vacuum leak? MAF sensor dirty? Should be some codes. don-ohio

2000 Ford Ranger... | Answered on Apr 18, 2017

Not finding what you are looking for?

924 questions posted

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Ranger Ford

  • Ranger Ford

Most Popular Question

2000 ford ranger plug snaps im

  • Cars & Trucks
Loading...