20 Most Recent 1998 Ford Crown Victoria Questions & Answers


1998 crown victoria My personal suggestion would be to go for these repair catalogs. I know this website reliable-store that i used to buy them from, and they sold online it was very good manual. Go ahead, I bet.

1998 Ford Crown... | Answered on Jan 22, 2018


Could be the motor, or the actuator arms binding. You will have to remove the cowl cover and observe the arms in action. make sure the connector grommets are present and in good condition. If so , probably motor is overheating and tripping circuit breaker.

1998 Ford Crown... | Answered on Nov 18, 2017


P1409 - EGR Vacuum Regulator Solenoid Circuit Malfunction This test checks the electrical function of the EGRVR solenoid. The test fails when the EGRVR circuit voltage is either too high or too low when compared to the expected voltage range. The EGR system must be enabled for the test to be completed.
  • EGRVR circuit open
  • VPWR open to EGRVR solenoid
  • EGRVR circuit short to VPWR or GND
  • Damaged EGRVR solenoid
  • Damaged PCM
The EGR vacuum regulator solenoid resistance is from 26 to 40 ohms.

1998 Ford Crown... | Answered on Nov 16, 2017


Replace what it is saying to replace.

1998 Ford Crown... | Answered on Jun 18, 2017


it should be in your owner manual. if not, I can look up something for you but can't post illustrations to this site.

1998 Ford Crown... | Answered on Oct 24, 2016


No I wouldn't think a short , but I would thing a ground circuit problem or a low voltage problem . Have the battery an charging system tested . Inspect vehicle grounds , look for lose or corroded terminals connections ! Do a voltage drop test on all electrical circuits ,power an grounds . Voltage Drop Testing Automotive Circuits Your going to need wiring diagrams of affected systems . You can find free wiring diagrams here http://bbbind.com/free_tsb.html

1998 Ford Crown... | Answered on Oct 11, 2016


You have to use a very small flathead screwdriver (the actual tool can be long, the flathead has to be small...) and there's a little notch on one side of the cover. Just insert the screwdriver there and gently pry it off. Good luck!

1998 Ford Crown... | Answered on Feb 17, 2016


without having any familiarity with your vehicle can I ask whether the change from 2 and 4 wd mode is achieved manually, i.e. via a lever or is it an automatically achieved transition...i.e. does the vehicles electronics achieve the shift.
If it is a manually achieved shift then I would suspect the transfer lever , or linkages , if it has any.
A transfer box usually has need of a service every two or three years or so of average driving, say 30 to 40 thousand miles.



Can you please add some more information and resubmit the query please

1998 Ford Crown... | Answered on Nov 05, 2015


Does the car start and idle fine?
If yes and the car looses power when you excelerate it may be a clogged fuel filter.

1998 Ford Crown... | Answered on Sep 21, 2015


heater core means you had the dash all apart , yes?
that means the computer wiring is in that mess too.
run a computer test 1st

1998 Ford Crown... | Answered on May 03, 2015


Sounds like a regulator issue which is built into the alternator. New alternator.

1998 Ford Crown... | Answered on Apr 29, 2015


There should only be two bolts holding it on all u have to do is disconnect the power wire then the ground wire and take the rwo bolts off and you should be fine.
If when u start the install of the new starter and the bolts are having a hard time lining up you can get a scissor jack to push it up in just the right spot. Also whenever your working with electricity disconnect the battery

1998 Ford Crown... | Answered on Apr 27, 2015


So you think you could hear the starter spin but the "band" did not turn? I suppose you mean the serpentine belt did not turn. It is quite possible for the starter to spin but the bendix to fail to engage the flywheel. This can be caused by low battery charge, bad battery connections, or more commonly, a bad starter.

1998 Ford Crown... | Answered on Jan 08, 2015

Not finding what you are looking for?
1998 Ford Crown Victoria Logo

427 questions posted

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Crown Victoria Ford

  • Crown Victoria Ford

Most Popular Question

1998 crown victoria replaced heater

  • Cars & Trucks
Loading...