20 Most Recent 1996 Ford Ranger SuperCab - Page 7 Questions & Answers

0helpful
2answers

I have no power to my coils on a 1996 ford ranger

Did you check the fuses and relays ? You may need to get a wiring diagram to trace the circuit back to the key switch.
7/3/2012 12:06:51 AM • 1996 Ford Ranger... • Answered on Jul 03, 2012
0helpful
1answer

96 4x4. has rumble at about 55 mph. seems to come from front.

it is very common after a wheel get hit the wheel bearing goes bad
6/24/2012 1:23:06 AM • 1996 Ford Ranger... • Answered on Jun 24, 2012
0helpful
1answer

Underhood fusebox fuse #13 50 amp what is it for

The large MAXI fuses in the engine compartment fuse block are the MAIN fuses. They supply voltage to several other fuses or circuits.MAXI Fuse #13 in your 1996 Ford Ranger is supposed to be a 30 Amp fuse (not a 50 Amp) according to the power distribution diagrams as well as the fuse block detail diagram. This fuse supplies voltage to the Powertrain Control Module (PCM) power relay and to the oxygen sensor heater circuits.Please note that it is NORMAL for this fuse to cause a draw on the battery during vehicle operation and also after engine shut down. The OBD-2 oxygen sensor heater circuit monitors run after engine shut down and key off. This can take up to 45 minutes to complete. After the O2 heater monitor has run, the PCM will go into sleep mode.When the PCM goes into sleep mode, the battery draw from this fuse will be reduced greatly. If you are performing "ignition-off-draw" tests trying to figure out why the battery keeps going dead, it is best to use an ammeter that has a 1 or 2 amp scale. You should set-up for the test using a shunt bar. Wait for 45 minutes to an hour for all of the computer systems in the vehicle to go into sleep mode, then open the shunt. Your computer memory, radio pre-sets, clock, etc. will continue to draw without ever shutting completely off. Any draw under 300 Milliamps is considered "acceptable". It is my experience that most vehicles have an ignition-off-draw of somewhere near 150 Milliamps.The underhood fuse box diagram can be found on page 314 in the 1996 Ford Ranger Owner's Manual.If you do not have an Owner's Manual, you can get a PDF version HERE (direct link)
5/16/2012 12:44:04 AM • 1996 Ford Ranger... • Answered on May 16, 2012
0helpful
1answer

Where is the manual transmission plug to check

If it is a stick it has a clutch master cylinder.
4/9/2012 5:21:55 AM • 1996 Ford Ranger... • Answered on Apr 09, 2012
0helpful
1answer

WI'll the crank shaft senser cause it to miss?

Yes it will. It is an important sensor that has to do with your vehicles timing. Below is a description of what it does. Hope this helps.....4_1_2012_1_24_33_pm.jpg
4/1/2012 1:24:39 PM • 1996 Ford Ranger... • Answered on Apr 01, 2012
0helpful
2answers

I need to locate the canister purge valve and the

look above the spare tire under the back of the box
2/26/2012 8:24:09 PM • 1996 Ford Ranger... • Answered on Feb 26, 2012
0helpful
1answer

How to check sending unit on 96 ranger

Which sending unit do you refer to, there are many to choose from
2/20/2012 9:19:47 PM • 1996 Ford Ranger... • Answered on Feb 20, 2012
0helpful
1answer

Location of canisterpurge solenoid/flowsensor 1996

It is located right next to the carbon canister under the truck on a tray that is mounted near the fuel tank.
11/23/2011 12:28:40 AM • 1996 Ford Ranger... • Answered on Nov 23, 2011
Not finding what you are looking for?
1996 Ford Ranger SuperCab Logo

744 questions posted

Ask a Question

Usually answered in minutes!

Top Ford Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Ranger Ford

  • Ranger Ford

Most Popular Question

cause 1996 ford ranger no going in gear

  • Cars & Trucks
Loading...