20 Most Recent 2000 Ford Explorer Questions & Answers

Ford Explorer and V8 O2 Sensor Locations diagram. This shows the location of Ford oxygen sensors on Bank 1 and Bank 2. If you want to know where your O2 sensors are, this diagram is your guide (click over pic for zoom)...


Hope helps with this (remember to rate and comment this answer).

2000 Ford... | Answered 13 hours ago

Getting fuels means??? Are the injectors getting a pulse,are the coils firing?Are all ground wires attached and all connectors attached and clean?If it does not start on starting fluid there may not be any spark.

2000 Ford... | Answered on Jan 22, 2019

How do I know it's my blower motor itself, blower motor resistor or a switchbox?

You view wiring diagrams an test electrical circuits with a DVOM - digital volt ohm meter .
Free wiring diagrams here http://www.bbbind.com/free-tsb
Enter vehicle info. year , make , model an engine size , Under system click on HVAC , under subsystem HVAC controls . Click the search button ,then the blue link.
Do you know how to do that ? Videos on youtube on electrical circuit testing .

2000 Ford... | Answered on Feb 12, 2018

Take it back to whatever shop installed the rebuilt engine and make them troubleshoot the problem. There are no coincidences ...
However, "loud thumping noises" don't sound good at all.

2000 Ford... | Answered on Feb 09, 2018

My mechanic disconnected the security section because my key I use to start the car had the security spot on the key was loose and would not work in the ignition It was going to cost a lot for a new set of keys so he took the security section out for a lot less. As he said an older car does not need security.

2000 Ford... | Answered on Dec 29, 2017

Fuel, Spark and Air are primary to starting car. Fuel tank definitely has fuel (some friendly neighbor didn't borrow yours)? How OLD is the gas - it can go bad. Must have spark if runs @ all. Anything clogging the air filter ? You've checked for rodent damage to wires/hoses under the hood/dash?

check for CEL codes - you can buy an OBD2 scanner for $20 @ Walmart.


2000 Ford... | Answered on Dec 22, 2017

P1506 - Idle Air Control (IAC) Overspeed Error This DTC is set when the PCM detects engine idle speed that is greater than the desired rpm.
  • IAC circuit short to GND
  • Damaged IAC valve
Disconnect IAC valve and look for little or no change in engine rpm as an indication of a stuck or damaged valve.
Ford Idle Air Control IAC valve test how to adjust minimum idle speed
Ford Idle Air Control Valve Diagnostics High Idle DTC P1506

2000 Ford... | Answered on Dec 05, 2017

you might have bad conection in the sockets
check to see if the light bulb fits snug in the sockets

2000 Ford... | Answered on Nov 07, 2017

You have a vacuum leak. Did you use new intake manifold gaskets and torque the bolts according to the spec? Did you get all of the vacuum lines back on in the right places?

2000 Ford... | Answered on Aug 31, 2017

What about inside engine , compression test?

2000 Ford... | Answered on Aug 21, 2017

Check the door unlock relay located in the AUX relay box #2 .
Auxiliary Relay Box #2, 2 Door w/Electronics Group
Left rear of vehicle, above wheelwell
Auxiliary Relay Box #2, 2 Door w/o Electronics Group
Left rear of vehicle, above wheelwell
Auxiliary Relay Box #2, 4 Door w/Electronics Group
Left rear of vehicle, above wheelwell
You need to take rear trim panel off to view this relay box. There is a seperate relay for lock

2000 Ford... | Answered on Aug 19, 2017

Hi, the problem could be the motor, controller, or resistor. You will have to troubleshoot using a volt/ohmmeter. If you have a meter and are willing to troubleshoot, I can send a procedure.

2000 Ford... | Answered on Jun 22, 2017

you need to remove the battery and check each connection from the circuit, test the feed from the live wire on the battery to the fuse just to find the pole on the fuse then the other end is where you need to put the matter, then check to ground any earth on the vehicle with ignition on, if it beeps on metter or goes 000 then it grounded and you need to up plug the connection to each electrical unit on its path to find the grounded wire or unit. check the reversing lights and the feed to the daytime lights. the day time light will have a main wire off the ignition to a relay so when the ignition is turned on the lights will come on. check this relay as some relays have a resister in them for the lights them self only if this is shorted replace the relay.

2000 Ford... | Answered on Jun 21, 2017

Not finding what you are looking for?

1,536 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

1998 Ford Explorer
1998 Ford Explorer

2,937 Questions

1996 Ford Explorer
1996 Ford Explorer

2,264 Questions

1999 Ford Explorer
1999 Ford Explorer

2,189 Questions

2002 Ford Explorer
2002 Ford Explorer

2,245 Questions

2004 Ford Explorer
2004 Ford Explorer

1,464 Questions

Top Ford Experts


Level 3 Expert

85111 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

gerry bissi

Level 3 Expert

4387 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Explorer Ford

  • Explorer Ford

Most Popular Question

changed upper intake manifold gaskets

  • Cars & Trucks