Top 10 1995 Ford F150 Styleside Regular Cab Questions & Answers

Is WHAT before or after filter?

Just in front of the side tank is the selector.Very common problem.The rear fuel tanks pump quits.

I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_a3369546f8067589

Automatic trans??? 2 or 4 wheel drive??
AOD 2 wd- 12.3 qts
AOD 4 wd - 12.3 qts
C-6 2 wd - 12.0 qts
C-6 4 wd- 13.5 qts
E40D 2 wd 15.7 qts
E40D 4wd 16.2 qts
4R7OW - 14 qts

change trans fluid and filter , possible get trasns flushed check electrical connections

Hi:
Your transmission has 3 shift rails...
1st - 2nd
3rd -4th
5th- Reverse

If your 1st and 2nd don't work , you have an internal transmission problem, such as a syncronizer, or similar fail... There is not much you can fix, without removeing the transmission.

1995 Ford F 150 Pickup 5.0 liter V-8 VIN "N"




I hope helps (remember to rate this).

Cylinders are numbers 1-2-3-4-5-6 from front of vehicle to the firewall. And the firing order is 1-5-3-6-2-4.

Removal & Installation

1. For the 1500HD, relieve the tension from the park brake cable by pulling down on the park brake cable in front of the equalizer then removing the cable from the equalizer bar.
   
2. For the 25/35 series Disable the park brake cable automatic adjuster.
   
3. Raise and safely support the vehicle.
   
4. Remove the tire and the wheel.
   
5. Perform the following procedure to remove the cable (2) from the backing plate (4):
   
   • Compress the spring (3) by pushing toward the lever (1).
     
   • Depress the locking tabs.
     
   • Pull the cable housing out of the backing plate (4).
     
   • Remove the cable (2) through the slot in the backing plate.
     

     Lever (1), cable (2), spring (3) and backing plate (4)
     

6. Remove the park brake cable (2) from the lever (1).
   
7. Remove the rotor.
   
8. Remove the rear axle shaft.
   
9. Remove the park brake shoe return spring (6).
   

   Park brake shoe assembly 1500HD, 25 and 35 Series
   Click to Enlarge

10. Remove the park brake shoe anchor springs and pins.
    
11. Separate the tips of the shoes from the park brake actuator and remove the park brake shoes and adjuster assembly from the vehicle.
    

To install:

1. Clean the debris and the dust from the park brake components using a clean shop cloth.
   
2. Install the adjuster assembly to the park brake shoes.
   
3. Separate the tips of the shoes and install the park brake shoes to the park brake actuator.
   
4. Install the park brake shoe anchor springs and pins.
   
5. Install the park brake shoe return spring (6).
   
6. Adjust the park brake shoe.
   
7. Install the rear axle shaft.
   
8. Install the rotor.
   
9. Install the park brake cable (2) to the lever (1).
   
10. Perform the following procedure to install the cable (2) to the backing plate (4):
    
    • Compress the spring (3) by pushing towards the lever (1).
      
    • Route the cable (2) through the slot in the backing plate.
      
    • Push the cable housing into the backing plate (4) until the locking tabs snap into place.
      
11. Install the tire and wheel.
    
12. Remove the safety stands.
    
13. Lower the vehicle.
    
14. Enable the park brake cable automatic adjuster.
    
15. For the 1500HD, install the park brake cable to the equalizer by pulling down on the park brake cable in front of the equalizer then installing the cable to the equalizer bar.
    
16. Adjust the park brake cable.
    

// // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 23; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]> var _strTreeScrollHidName = 'ctl00_hidTreeScrollPos';

it fuel pump is bad or you have a short somewhere in the ignition

asked and answered