20 Most Recent
1987 Dodge Ram Maxivan Questions & Answers
I have 1987 dodge ram b250 van and i just changed
Try connecting plastic tubing to drivers side bleeder valve. Place end of tube into a half full can of brake fluid. Press the brake repeatedly with the engine running so your power braking system is working. Watch the tubing until all bubbles have been pushed through the tubing. Repeat for the passenger side. The plastic tubing needs to be submerged in the fluid in the can to keep it from letting air back into the system through the bleeder valve.
I have a 2002 Mercury Mountaineer that has a
Must likely your brake pads are worn out and the steel backing is in contact with the rotor. Better get it looked at quickly otherwise you will have to have the rotors ground or replaced as well as new pads.
1987 Dooge Ram 2.6 Overheating -- tried replacing
One note- many thermostat elements can be installed backwards and while they will function, they don't allow full flow of the coolant like that.
Dunno what the bolt might be for-
Another possibility is a blown head gasket; if these fail between any combustion chamber and a coolant path, it will heat the devil out of coolant and generally cause exhaust fumes in bubbles in the cooling system.
You can check for signs of rust on your plugs since the cooling engine will **** in coolant and that will leave deposits.
Also check your coolant for any signs of a milkiness and your oil for signs it is turning into hand-lotion.
How much does a brake repair kit for a 87 dodge
My personal opinion is you don't want to rebuild a caliper. Most times now calipers are replaced as a unit (you can replace just one side without a problem) as the labor and time to work on a caliper is offset by the price of a new or rebuilt unit from a parts store. I don't have the pricing for your particular vehicle, but a phone call to an auto parts store can get you a price and availability instantly. I'm not sure if most auto supply stores would even stock the pistons and seals needed for the rebuild job.
How do you fix sticking caliper pistons
If its the piston thats sticking you can purchase a kit for it but your probably better off buying the caliper. If the caliper is sticking and not sliding back and forth you need to buy a brake hardware kit for it. From my experience the brake hose usally collapses on the inside and causes it to stick you might want to check this out.
No spack to the spack plugs i think it mite be an
Trace the secondary wire from the distributor cap to the coil pack.Using a test lamp see if you have voltage to the pack with the key on.if not,you may be correct if you do have voltage the coil is likely defective.Also check the cap and cable connection at the distributor cap
Does a 1987 dodge ram 100 have a ballast resistor?
yes it is in one of two places.The first is look under the hood find the blower motor on the left side standing infront of the van.look under the blower motor to the right and down it should be there.if not look near the center/rear engin compartment,to see if it is there.It is a white ceramic part about 2/3 inches long with twqo wires on it.
How come why my 98 Dodge ram starts and runs fine but when I switch it off it won't start back up
no ca/truckr model told at all, of many 3 or 4.no engine told and is and engine problem.the VIN digit #8 is the engine codeNO model told.ram 1500 ?, 2500, 3500 or 4000 , and not the Ram van. 1998 (4000 Mexico or Canada)no engine told one is Diesel;, 3.9 L Magnum V65.2 L Magnum V85.9 L Magnum V85.9 L Cummins turbo-diesel I6<<< ill not cover this ever.8.0 L Magnum V10does the starter motor always work correctly every time, called cranking?we get the fact it does not start. sometimesbut what is not clear, at all, is that the starter always makes this sound called cranking? or fails to do crankingsee MP3 post
Not finding what you are looking for?