20 Most Recent
1984 Dodge Rampage - Page 8 Questions & Answers
I have a 2008 dodge avenger that leaks oil onto the engine and therefore creates smoke
It might be the Timing Cover Seal. I'd had to have one replaced on a Pontiac Grand Prix, where oil had been spitting up from it, causing the Serpentine Belt to get oily and slip. The Harmonic Balancer had to come off to get to it. The leak on my car at the time had stopped after that seal was replaces. The tire had to come off, the plastic mud guards, too. Google Search had turned up some Timing Case Cover Gaskets that ran up to around $20. Another site had turned up a Timing Cover Seal for around $7. Autozone sells those parts, too. That could be the part he had been talking about. Not positive. Perhaps the local parts store could advise further.
1975 dodge sportsman rv ignition tumbler removal and replacement
To replace the ignition tumbler in a 1975 Dodge Sportsman RV, you will need to follow these steps:
- Remove the steering column cover: Start by removing the screws or bolts that hold the steering column cover in place. Once the cover is removed, you should be able to access the ignition switch and tumbler.
- Disconnect the electrical connections: There should be two electrical connections that attach to the ignition switch. Disconnect these before attempting to remove the tumbler.
- Remove the retaining screw: Use a screwdriver to remove the retaining screw that holds the tumbler in place.
- Remove the tumbler: After removing the screw, the tumbler should slide out of the ignition switch.
- Install the new tumbler: Insert the new tumbler into the ignition switch, making sure it is securely in place.
- Reinstall the retaining screw: Use the screwdriver to reinstall the retaining screw.
- Reconnect the electrical connections: Reconnect the two electrical connections that you disconnected in step 2.
- Replace the steering column cover: Once everything is back in place, replace the steering column cover and secure it with the screws or bolts.
- Test the new tumbler: Finally, test the new tumbler to make sure it is working properly and that the RV starts and runs smoothly.
Find orifice tube on 2007 dodge caliber
HVAC QUESTION, ???? A./C not cold, can we have problem told first and not a blind out of context hunt?
HVAC
IN THE DASH IS THE EVAP CORE
AND I BET IT IS NOT BAD. UNLESS COMPRESSOR EXPLODED IN SIDE.
dodge says
the variable A/C orifice tube provides improved A/C system cooling during city driving and when under heavy loads by controlling refrigerant flow through the two parallel flow paths integral to the orifice tube. Under normal loads, the refrigerant flows through the inlet filter screen, the fixed and variable ports and both metering orifices. As the load on the A/C system increases, the temperature of the refrigerant leaving the A/C condenser increases, which causes the bi-metal coil to expand and restrict the flow of refrigerant through the variable port of the tube. Restricting the flow of refrigerant through the variable port and its orifice provides a greater pressure differential between the high and low pressure sides of the A/C system, resulting in colder refrigerant vapor traveling through the A/C evaporator to help remove the heat from the conditioned air flowing into the passenger compartment.The A/C orifice tube is not serviceable and the A/C liquid line must be replaced if the orifice tube is found inoperative
2001 Dodge Magnum 1500 with 3.9 v-6, 5 speed manual transmission won't come out of reverse after replacing the clutch, pressure plate and the throw out bearing..
magnum? a RAM 1500 pickup, i guess magnum is engine jargon?
well it is not really stuck in reverse (well unless is. blush)
but 99%^ of the time that means the clutch is 100% dead.
learn this trick
have a buddy wiggle the truck on say flat garage floor, (no brakes set)
jug it forward and reverse the whole car and you wiggle the shift lever to N
see it does N.
the box has hard cut gears and synchro dogs. and if under pressure huge
the shifter level sticks. all manuals do that, with a dead clutch.
can do it.
do not gorrilla the shift lever or wreck the gear dog forks inside. box.
fix the clutch.
the clutch actuator is dead,. never replace any clutch first
gee my 4wd is 15 hard hours labor to that and I never do , unless MUST/
the best plan on any 22 year old car/clutch is a
new master cylinder and slave kit. first
and learn now to bleed, clutch lines, that are a horror to do .
ok? the fluid in the lines run up/down verically
and the air bubble float up,. making bleeding super hard and confusing to many
. there are tools that make this easy , Pressure bleeding kits.
https://www.rockauto.com/en/catalog/dodge,2001,ram+1500+pickup,3.9l+v6,1366578,transmission-manual,clutch+master+&+slave+cylinder+assembly,10290
we make sure this is working first. 100% full stroke or the clutch is useless.
and locked up fully engaged.
at the least it must be bled fully. off all air.
Not finding what you are looking for?