20 Most Recent 2000 Dodge Ram 3500 Questions & Answers


dealer not interested in your problem
low vacuum at idle ( normally 15 inches of mg) indicates problem intake valves
check the valve clearance ( .010"intake hot .012" exhaust hot)
you can set it the same cold as the settings will change but still be within specs for the hydraulic followers to compensate
the firing order could have 2 ht leads crossed and that will also cause low vacuum

2000 Dodge Ram... | Answered on Dec 22, 2017


Usually a wiring problem - the wiring on your truck connector may not match the pinout on the trailer plug.

2000 Dodge Ram... | Answered on Oct 10, 2017


I'd suspect that the gauge is just tired. Check the voltage at the battery with a multi meter while the engine is running. At idle, if you are anywhere near 14V (13.8-14.5) you are fine.

2000 Dodge Ram... | Answered on Sep 29, 2017


Check crankshaft sensor.

2000 Dodge Ram... | Answered on May 12, 2017


100 PSI is way to low, I think you have a burnt valve. Check the cylinder compression on all cylinders, no cylinder should be 5% lower than the highest cylinder pressure measured or the engine will run rough or misfire.

2000 Dodge Ram... | Answered on Feb 08, 2017


the idle air control is on the back of the throttle body. it has a plug going to it and is held to the throttle body with 2 screws

2000 Dodge Ram... | Answered on May 25, 2016


Hi Dennis if there's difficulty changing gear. Or if it slips under pressure like going up a hill the motor revs up but the speed of the vehicle dosent change. Regards Jim...

2000 Dodge Ram... | Answered on May 09, 2015


cluster or bus wires going down, test bus voltage to cluster,if reference voltage ok to cluster then internally a cluster issue,best place to start diagnosis.

2000 Dodge Ram... | Answered on Feb 03, 2015


check the under hood fuse block/relay box,ive seen these go bad, i see you said starter was checked how was it check .also check to see if getting power to starter when you turn to crank,will have to have friend help you,if the test light lights up,give that starter a big smack with bfh! is there a sercurity light coming on and staying on,if so check your key,it could be worn out.there is a starter relay that controls starting is this a stck or auto,good luck,mike

2000 Dodge Ram... | Answered on Jan 20, 2015


2000 dodge ram 2500 truck 4wd the abs light and air bag light were on then the check engine light went on then all of a sudden all the gauges and warning lights went dead and off including the tach and other gauges. But now all the gauges are working and the check engine light went off with all the others and the tach and other gauges are working. what is the problem with this truck ? The only code it read was p1687 from the dtc. Is the problem the pcm or something else.

2000 Dodge Ram... | Answered on Dec 15, 2014


Is it auto or manual?? If it's manual I would say your clutch has thrown in the towel, if it's auto if could be transmission oil dirty and will need replacing, hope this helps

2000 Dodge Ram... | Answered on Aug 30, 2014

Not finding what you are looking for?
Cars & Trucks Logo

198 questions posted

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

84625 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Ram 3500 Dodge

  • Ram 3500 Dodge

Most Popular Question

dodge 2000 3500 4x4 turn signals

  • Cars & Trucks
Loading...