20 Most Recent 1994 Chevrolet S-10 Blazer Questions & Answers


There are two screws on either side of the armrest. Remove with Allen wrench or Phillips head. Be sure the armrest is closed position. After removing screws lift straight up to remove the armrest. Save the screws.

1994 Chevrolet... | Answered on Sep 01, 2019


open the drivers door and look at the corner of the dashboard. a snap on lid you will see that is the fuse box

1994 Chevrolet... | Answered on Dec 31, 2017


The fuse box is in the engine compartment on the fender on the drivers side. Plastic black box with a lid that comes off.

1994 Chevrolet... | Answered on Dec 31, 2017


that will be carbon dust from running too rich . cat replacement may cure it

1994 Chevrolet... | Answered on Oct 21, 2017


Leaking fuel pressure regulator , or leaking injector's ,depends on injection system . ! it's only running rich on right bank. whatever that means . Your vehicle is a v - 6 has two banks . right side of the engine an left side of the engine . Bank 1 is where #1 spark plug is . bank 1 is odd numbers 1-3-5 Bank 2 is even firing #'s 2-4-6 . What fuel injection system does it have ?
Your best bet mite be to take your vehicle to a qualified repair shop.

1994 Chevrolet... | Answered on Oct 05, 2017


no,you will need to siphon the gas out of the tank.before you do,remove the gas cap,have someone turn the ignition on,while you stand by the tank.the fuel pump should run for a second or two. if it does ,I doubt it is the fuel pump,if it does't,it probably is

1994 Chevrolet... | Answered on Oct 01, 2017


The Ignition Control Module is located: Under hood, center, rear engine area, mounted in distributor

1994 Chevrolet... | Answered on Aug 30, 2017


Check connection on brake switch and test with multimeter.

1994 Chevrolet... | Answered on Aug 10, 2017


The leak at the electrical plug.. can you tell if its coming from around the edge(s).. or coming through the wires them selves(around the wires)..If you just want the leak to stop, you could remove the plug and replace the o-ring or what ever type seal is there... If its coming through the wire area (wires themselves),, you can use some devcon 2 ton epoxy..(clear and liquid you mix)
DEVCON 2 TON EPOXY 84fl oz SYRINGE Walmart com
.. about the length of the dipstick..not sure.. a "junk yard" may have one cheap...

1994 Chevrolet... | Answered on Aug 02, 2017


Could be one of many things. Have you check the catalytic converter? This will get loud, but if you can remove the O2 sensor before the cat try to repeat the fail. This will relieve the back pressure. If the problem goes away you probably need a new cat.

1994 Chevrolet... | Answered on Jul 11, 2017


If it is the water pump there is a weep hole on it. That may be where it is leaking. Or it could be a frost plug.

1994 Chevrolet... | Answered on Jun 14, 2017


if it's carburated, make sure your butterflies are opening.

1994 Chevrolet... | Answered on Apr 27, 2017


probably the injectors are not working
run the fault codes or have the injectors for those cylinders checked
check wiring connections for the harness

1994 Chevrolet... | Answered on Mar 31, 2017

Not finding what you are looking for?
1994 Chevrolet S-10 Blazer Logo

1,357 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Blazer Chevrolet

  • Blazer Chevrolet

Most Popular Question

1994 chevy s10 blazer drive shaft only

  • Cars & Trucks
Loading...