2004 GMC Sierra - Page 2 - Answered Questions & Fixed issues

it is located under the steering column. you'll only need to remove the knee board cover. it sits in a large bracket. see picture

you can look it up at autozone library if the dash has to come out ,if that's the case 6-8 hr

Auto Repair Estimates Know How Much Car Repair Costs AutoMD use that link, enter your year make model engine size and zip code for an estimate

behind the starter. utube has video that can help

Missing Egr Valve 1999 2006 2007 2013 Chevrolet Silverado GMC Sierra 1500

It is in the under hood fuse box ABS 60amp ! An one in the instrument panel fuse box .BRAKE fuse 10amp . Fuse Block - I/P Left side of I/P behind access panel , open left door there is a access panel at the end of dash ! Hope i explained that good enough ! Now then what kind of problem are you having ? Maybe I can help ! ABS light lit on the dash , or maybe it doesn't light at all ?

check that the outside pad is still in the correct position as they can become dislodged when putting over the disc rotor.

sounds like fuel pump

I would unhook the battery for about 10 minutes, hook it back up then see what it does, if that doesn't work check battery, or go to owners manual to reset system.

Sounds like a bearing problem. The gears are held in place by roller bearings, and they sometimes pack up. Working the machine with a bad bearing eventually grinds up the steel balls or rollers that the flanges roll on, and the bearing collapses completely. The bearing itself will announce its demise with a grinding sound, and worst case scenario the bearing is so far gone that the gears are running out of true with respect to one another, and this could be the grinding you are hearing.

bad sensor

Often lights under a dash or indicators just blow out bulbs. If more than one thing isn't lighting and are centralized check fuses to see if its blown. Bulb or fuse. IMHO. MIGHT be a sensor on tranny too. Hope not. Here's a video with detaile dinstrauctions and other people's fuse questions. New fuses? Kind Regards, Scott Interior Fuse Box Location 1999 2007 GMC Sierra 2500 HD 2004 GMC Sierra... Amazon com Fuses Fuses Accessories Automotive 2004 GMC Sierra fuse box Questions Kind Regards, Scott

First off did you Know this ?????

Make / Models : Model/Build Years:
GMC / 1500 2004
Regency / Chevrolet 1500 2004
MANUFACTURER: General Motors Corp.
NHTSA CAMPAIGN ID Number : 04V240000 Recall Date : MAY 14, 2004
COMPONENT: Tires: Temporary/Emergency Spare Tire
Potential Number Of Units Affected : 285
SUMMARY:
The spare tire and wheel assembly that was provided on certain conversion vehicles will not fit on the front wheel hub due to offset of the wheel. However, it will fit on the rear wheels.
CONSEQUENCE:
If someone has a flat tire on the front wheel, they will not be able to install the provided spare tire.
REMEDY:
Dealers will install a spare wheel with the correct offset. Owner notification began on June 11, 2004. Owners should contact Regency at 1-800-989-4727.
NOTES:
Customers can also contact The National Highway Traffic Safety Administration's Auto Safety Hotline at 1-888-DASH-2-DOT (1-888-327-4236)

SPARE TIRE is Under rear of truck use Long Cranking in HoleClose to Lisence Plate to Lower it Down Cranking Counter Clockwise. Wing in center of Wheel pokes thrugh Hole in Center of wheel
Reverse Procedure to Put old tire in Tire Storage Compartment

1. Locate Jack & Wheel Lug Nut Wrench
2. There is Directions as to where to placse the Jack for raising Truck Where Jack is Located
3. Set Park Brake Chalk tire if possible & Hazard lights (If on the Roadside)
4. Loosen all Wheel Nuts on said wheel before Raising Vehicle
5. Place Jack In Recomended Placment spot
6. Rear is Normaly on Axel close to Shock
7. Front is Normaly on FRAMERAIL
8. Raise vehicle untill tire is 3-4 inches off ground as Flat will Lower vehicle
9. Remove All Wheel Nuts And Wheel
10. Place new wheel/tire on Vehicle and start all nuts
11. Tighten nuts as tight as Possible then Lower Vehicle Untill tire touches ground Good
12. Now Toque Wheel Nuts as tight as Possible with hand tool
13. Lower vehicle all the way down
14. Put away tools and Reliece Park Brake
15. Torque should be around 100-130 foot Pounds

I Hope this is What You Wanted Its Off the Cuff as My Reference Books done have this Procedure.

is there an evap code in the computer? normally this is caused by a pinched or stopped up evap line or the vent solenoid is bad not allowing the system to vent pressure which is causing it not to take fuel at a normal rate

Replacing a battery won't cause this unless you happen to hook it up wrong. In that case, check fuses, All of them. If they are all good, start replacing all those parts to include some computers.

blown bulb or perhaps if you bought it used the bulb was taken out?

Sounds like bad door switches. Can be a bad module as well.

Scanned ?? Code(s) stored ?? If you need further help, reach me via phone at https://www.6ya.com/expert/ralph_2f0886b7d6af32ce

No.....Sealed Assy.... If you need further help, reach me via phone at https://www.6ya.com/expert/ralph_2f0886b7d6af32ce

1 Scan/ck for code(s) 2 With scanner connected,road test vehicle/ck scanned parameters If you need further help, reach me via phone at https://www.6ya.com/expert/ralph_2f0886b7d6af32ce