20 Most Recent
1992 Ford Crown Victoria - Page 4 Questions & Answers
HOW DO I CLEAR THE AIRBAG CODES ON A 1992 CROWN VICTORIA
hi there, try the following link, i could explain it all but it is better if you can view the link with pictures etc to get a better understanding of what you are dealing with:www.crownvic.net/ubbthreads/ubbthreads.php?ubb=showflat&number=2339714hope this solves your problem
How to install break pads
Front aren't to bad just remove tire.Caliper holds pads, there are to bolts to be removed they may be allen wrench type from back to front One on the top one on bottom of caliper. After removing and a small amount of wiggling should allow you to tip the caliper back away from rotor and allow you to unsnap pads from caliper. Next you need a large C-clamp you use this to slowly push cylinder back into caliper, The cylinder has to go all the way back in or after you install new pads you wont be able to get them back down over rotor.Once you have pads set in caliper replace caliper over rotor and replace bolts in caliper pads are changed. BUT before taking off with vehical drive back and forth to ensure the brake pads properly set up and that you have brakes before taking off down the road.ONE other thing you may encounter,after removing bolts to take caliper off there are to spacers that slide with bolts as brakes wear.These to spacers have to be pushed into the caliper to allow you to be able to get the calipers properly seated on rotor. These spacers are seated in rubber and sometimes you have to drive them back in, be careful with the brake line so you don't break it while changing brakes it does Not have to be taken off to change the pads.Good luck let me know how it goes.
My 92 crown vic has blinking headlights when driving
The headlight switch has a built in 22 amp circuit breaker. It maybe doing it's job by opening and closing to prevent an electrical wire from burning. It opens when there is a 12 volt positive short to ground (negative). This may be caused by something as simple as a bad or damaged bulb. ( pull the headlight switch to the first position. does the parking lights blink on and off? if so then the short is in the parking light circuit. If not, then pull the switch all the way out. Does the headlights blink on and off? if so then the short is in the headlight circuit.) Check high and low beams. When the lights are on, visually look to see if any light is not working. If there is a light not working, it may be the point of the short. The built in circuit breaker may also be shorting due to a damaged wire to a light caused by body damage, road salt corrosion, a wire that has fallen against the exhaust manifold, a pinched wire going to the license lamp, or other condition that would damage a wire.
Where is the headlight fuse located on a 92 ford crown victoria?
If you are keeping this vehicle and do your own work on it, I 'd recomend going to ebay and buying a original Ford EVTM (electrical vacuum troubleshooting manual) for your specific vehicle. It is a very simple and well illustrated book to understand.I have one for my 1992 crown vic. It show a 40 amp fuse in the engine compartment fuse box for the lights.
I have a 1992 crown Victoria and my head light and
It is located on your steering column. The cover on the column is either held on with 5.5mm hex head blots or phillip's head screws. The switch itself can be held on with phillips, torx, or security torx bits. Sometimes loosening the mounting bolts on your steering column makes the job easier.
Backfire through intake
your timing is off, loosen the dis. hold down bolt at the base and adjust your distribitor alittle at a time/ but give it a min or 2 for the computor to adjust with it(while its running) and be sure to check your spark plug wires at dis. for cracks, missing insulation for it just might shock ya
How to remove egr valve from pacifica
It's on the drivers side between the back valve cover and exhaust pipe. Disconnect neg battery cable, disconnect wiring harness to EGR. unbolt tube going to EGR unbolt EGR
Car won't shut off
That happened to me years ago,so i may not be acurate on this but try this anyways...check the wires between the starter solenoid - aternator - and wiring whip to the vehicle,i think its a single light gray wire you would be looking for.check to see if its broken or shorted out...this info may not be right where to look,but i know its in that area.
My 1992 crown vic is not getting any gas to the
fuel pump is in the gas tank. Have to drop the gas tank. Make sure that u run all tghe gas out before u drop the tank. Also make sure that u mark how the old pump comes out and put back the same way so the float will work. Watch for the wires on the pump that u do not break any of them.
Not finding what you are looking for?