20 Most Recent 1989 Oldsmobile Ninety Eight - Page 3 Questions & Answers

Yes you can try this website car-part.com. They are a national listing for salvage parts throughout the united states. Just plug in the year, make, and model of your car.

hi you normally find 02 sensors on the manifold from the engine just locate the manifold on the engine and look down to the floor, you might see a metal type tube with wires on it sticking out,or it could be part way along the exhaust under the car look for the same thing and that will be it...hope this helps

Should not be too difficult if you apply pressure to the tensioner pulley for the serpentine belt (making it easier to remove). After disconnecting the negative battery cable you can then remove the Alternator.

tr replacing the flasher unit if the emergency flasher is the same just swap them out if not you will need to buy one. If you do get a new on get a Mechanical flasher not the electronic they seem to go out faster believe it or not. Hope this helps get back to me if that does not help and thanks for using fix-ya.

You need a new headlight switch. The headlight switch runs the instrument lights in addition to the parking and headlights. There is a rheostat that wears out over a period of years causing the instrument lights to fail. Thank you, Dana.

Hi,

In your case a Holley Blue pump and 5/16 line and it works great.

Thanks
Fame !

If your battery has any considerable age on it,( 2-5years), it could indicate a dead cell in the battery. If you installed an other than factory stereo then you could be getting drain there. If the battery is new, then check your battery terminal connections ensuring they are clean and tight. Also, check your battery cables to ensure they are tight at the engine block and at the starter. You might as well while you have the hood open, check the alternator connections for loose or corroded plug or fasteners.

ck relays, fuses, loose connections etc....have solnoid on starter checked, as well as the starter and battery. we all get bad ones every now and then.

Check number on ECM if it has the number 1228253 replace it because they will give a stalling problem.

open trunk remove screws or nuts from inside trunk undo wires and reinstall new one.hope i helped..

Your going to need to use a harmonic balancer puller to take it off, if you don't have one you can lone one out from Auto Zone and they can give you the step by step instructions to getting the job done, keep me posted, be glad to help.

Have you tried looking on the inside of the drivers door (when you open the door) Sometimes it will be on a label on the door or the door frame. Sometimes it also on the passenger side or on the glove box lid.

check under the brake to see if sensor is moving in and out. Then check the wires attached.

Check for a faulty ground to the 3rd brake light. A lot of wiring between it and the signal switch that feeds power to the 3rd brake light. Hope this helps

there is a sticker on the door jam likely on the drivers side with the recommended tire size... if it's not there let me know and i will find it for you

Robert

First there are 2 screws behind the steering wheel they are hex or phillips
take them out and it come s out then you need a socket to remove the nut and a puller to take the wheel off. Once you are to that point it is very complicated.
from hear on out. it took over 4hrs to remove mine down to the titlwheel section.
there is a spring behind the metal plate that you see and you have to press down
on that metal plate to get the c clip off with a special tool that you have to get
it presses down on that plate to release the spring , which take pressure of to get
at the c clip there are lots of srews and small parts inside be careful not to lose them!!!!

check the heater blower motor resistor not entirely sure where it is on your vehicle but they are always located near the fan in the heater box
you may also want to check the fan speed switch as well as the heater fuse in your fuse box
Hope This Helps.Good luck

Hi the starter motoris sticking thats the noise 2 options here:

1. give it smack with a hammer to unstick it

2. change the starter (recommened)

Hope this helps