20 Most Recent 1998 Chevrolet Corvette Questions & Answers


If the alternator has a bad bearing or bearings it would likely make a noise.

1998 Chevrolet... | Answered on Oct 18, 2017


Could be bad TPS sensor.

1998 Chevrolet... | Answered on Apr 09, 2017


a good battery will hold a charge through the winter if disconected from the vehicle adn left fully charged.
you may want to look into a battery monitoring charger, it is a trickle charger that is designed for long term use, it monitors battery volts and turns on when needed.

also put carpet squares or cardboard under the tires if you are parking on concreet. this will help prevent dry rot and flat spots

1998 Chevrolet... | Answered on Dec 19, 2016


Check to make sure you are getting power to the wiper motors. Also check relay. Either one could be bad.

1998 Chevrolet... | Answered on Aug 26, 2016


Check under the dash or on the sides of the dash with doors open, or under the hood in a box marked fuse relay. In most GM cars and trucks these are the places where thay stash the fuses

1998 Chevrolet... | Answered on Aug 26, 2016


the knock sensors are on the side of the engine block. they screw directly into the block. most easily accessed with the car raised up

1998 Chevrolet... | Answered on Feb 02, 2016


If the security light is blinking it will not start. The security system needs to be reset. You will have to have a fully charged battery to reset the system. With a full charged battery turn the ignition forward until the warning lights come on and leave the key in the on position for 15min. Turn key off and wait 10sec. then try and start.You may have to perform this procedure a couple of times, however, it is usually successful the first try. The reduced power light can be set by a low voltage/poor charge battery

1998 Chevrolet... | Answered on Apr 12, 2015


try this steps to adjust your wiper.
1. Place the keys in the ignition, turn the keys to accessory mode (key-on/engine off), and make sure the wiper motor switch is in the off position. Turn the ignition switch to the off position and remove the keys. The wiper arms are now in their parked position, although may not be properly aligned.
2. Access the bottom of the compromised wiper blade arm. You may have to open the hood or remove the wiper arm cowling (refer to the owners manual for the removal of the cowling on your specific vehicle if required).
3. Locate the retaining nut at the bottom of the wiper arm assembly. Some models will have a protective plastic cap covering the nut. Other vehicles may have a hinged cover that is part of the wiper arm itself. Pry the cap off with a straight-edge screwdriver or unsnap the hinged cover by prying it up from the bottom of the wiper arm with the screwdriver to reveal the retaining nut.
4. Hold the wiper arm stable with one hand and remove the nut with the ratchet and a socket with the other.
5. wiggle the wiper arm gently with one hand while gently prying the base of the arm off the splinter wiper arm stud. The stud has a small spline that holds the wiper arm in the correct position unless otherwise compromised. The wiper arm will feel secured to the stud, but the combination of wiggling gently and prying with the screwdriver will work to remove the arm.
6. Place the arm back into the splined wiper arm stud by positioning it in the off position. some vehicles may have a wiper arms stop that the arm rests in the off position. If so, make sure that the wiper arm is resting against the wiper arm stop when replacing it on the stud.
7. Replace the retaining nut and tighten with the ratchet socket. repaet this procedure with the other wiper arm if desired.
8. use 2 sets of pliers to bend the wiper arm back into position if the wiper arm has been bent. Hold the wiper arm with one set of pliers to anchor it and use the other set to bend it so the wiper is perpendicular to the windshield. If the arm is bent too badly,replacing the wiper arm maybe a more viable option.
9. Inspect the wiper blades.check them for tears in the rubber blades, dry cracking or flimsiness.Replace the wiper blades if necessary.

1998 Chevrolet... | Answered on Dec 08, 2014


I think the antenna wire is permanently attached to the glass and plugs into the power antenna motor

1998 Chevrolet... | Answered on Dec 01, 2014


Failure in Evap System-- a possible place to
start some TESTING

1998 Chevrolet... | Answered on Jul 31, 2014


any number of things can cause that, like an old/dirty oxygen sensor. some things aren't worth fixing while others are, but don't sweat it as long as all your other gauges are in the green and your car still runs, I've run cars for years with engine lights on, its certainly not something to rush anywhere for.

1998 Chevrolet... | Answered on May 23, 2014


In the underhood electrical center.
The fuse number is 13 and its a 20A mini fuse.

1998 Chevrolet... | Answered on Apr 07, 2014


could be several things a shift solenoid in trans ....possibly clogged filter...maybe alinkage problem

1998 Chevrolet... | Answered on Oct 30, 2013

Not finding what you are looking for?
1998 Chevrolet Corvette Logo

Popular Tags

224 questions posted

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85161 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Corvette Chevrolet

  • Corvette Chevrolet

Most Popular Question

1998 corvette will not start says

  • Cars & Trucks
Loading...