Top 20 2001 Mercedes-Benz CLK-Class Questions & Answers

code p 0455 refers to evaporative emission (EVAP) system---large leak detected ====causes --hose connection/s---intake leak-----EVAP canister--EVAP canister purge valve the first place to check for a large leak is the filler cap properly installed and tightened

What about the ignition coils and spark leads?

It will need to be scanned for fault codes. most likely and wheel speed sensor fault in this age of car.

You need to have your ECU read, you can buy a ODB reader online for around 10bucks. Work with Bluetooth in sync with your phone. This way you can read error codes the ODB reader lists, look them up on the net and then take it from there. For me, i helped alot when i had issues with my engine management light going on after i replaces parts on the block. I need to check whether your car is using ODB or ODB2 port for the reader. Being i 2002 model im guess ODB, but have a look online. Do alot of work on cars, except i dont have much experience with automatic transmission car's as we don't drive them much in Europe, we want pure performance :)

I believe you do not remove the lens - rather you open the trunk and find the back of the lamp (you'll have to remove the panel in front of it) and remove and change the bulbs from inside the trunk.

wheel bearings should have no play at all The correct adjustment is no preload -no end float with the adjustment nut moved slightly to preload to fit the pin. It is happening on full lock ,check the full lock stop as the tyre may be hitting on the suspension or inner guard.

Bad alternator means no battery charge. Run the battery down without a charging means no power and engine will die. Charge the battery and put a meter on it to see if it goes to 14 volts with engine running. If stays under 13 volts with engine running, replace the alternator.

check the adjustment of the roof position switch /sensor . If it is activated then the switch/ sensor may be faulty.

Bad wiring? The wires that go between the car body and doors or in the center console - has someone spilled some coffee or drink in the center console? Is it just one window or several? (just one - I suspect door, several I suspect center console).

You need to have the Freon checked in the A/C system. If that is ok check to see if there is power going to the compressor clutch. Low Freon will keep the system from working.

Have to find out why the fuse blowsWhat is wrong with that circuitThen you see if you have another problemcausing it to go into limp modeIf you look at a wiring diagram & had a factorymanua,l you could learn the vehicle strategyWithout both, your pretty much done & have topay a shop that won't educate you, if they evenhave a clue

Remove the kick starter, check if the solenoid is okay and if not replace or service.

Test battery charge, jump the battery to start and check battery charge, sound like a alternator or voltageregulator wrong there.

Lots of things can trigger the CEL (check engine light) and cause the vehicle to lose power. Without knowing what code(s) are stored in the computer, this is all jut a guessing game. Take it to a mechanic or pull the codes with an OBD reader.

Yes, the wheel bearing play is adjustable on your vehicle. It is not really hard to do, however it requires special tools (pullers) to remove the hub assembly cover without damaging things.

The mechanisms for the top are located in the trunk of the car. There are some trims you need to remove to access the hydraulic actuators and pump. If the pump's oil level was low it might have tried to operator the top unevenly and caused a jam, or there is just not enough fluid to operate the system. Also, the pump has been reported as giving problems, as has the electrical supply to it. There are several switches catches, hooks and levers in the system which could give problems, but the whole operation is electronically controlled. The best way to override the system would be to disconnect the hydraulic lines from the actuators and then move the hood manually. Just remember to have something to catch the fluid that will come out of the disconnected pipes.

You will never know what your getting,period

A dealer has no reason to be honest,they want
your money

That is one expensive car to maintain

Do you need a Mercedes to impress clients?

Try pushing the gear shift further forward in park with your hand and see if the key releases.

If this fails it may be the switch itself just under the centre console which surrounds your gear shift. Carefully but firmly pull up the centre console up and you will see a little 'plunger' switch the engages when the gear shift is at its furthest travel forward in park.

The soft top control module should reset every time the ignition switch is off and the key is pulled out. There are two types of flashes. If the switch flashes fast it means the luggage cover in the trunk is not in place. If the light flashes slow it means there is an electrical problem. Meaning the control module is not seeing one of the micro-switches in the correct position. You can try manually opening and closing the soft top by locating the pressure relief screw in the back of the trunk. There will be a little flap of carpet towards the left center. Use a flat blade screwdriver to turn the bleeder screw to the left. This allows the hydraulic fluid to bypass the pump so that the top can be moved manually. You will need a 5mm allen to unlock/lock the latches.. Double check in the owners manual there might be illustrations I can't remember for sure if it does or doesn't.

start the car, if stop like after half an our to one our, and then after one our again start fine and can drive another 15 minute, again same thing happen and continue the same. is the problem same in your car, faulty crank angle sensor replace crank angle sensor,