20 Most Recent 2000 Chevrolet Tahoe - Page 2 Questions & Answers


ok so unplug the thing and stick a voltmeter in it, the hot side is obvious-if neither side is hot then you know you need to start troubleshooting the circuit-I would start with the brake fuse.

2000 Chevrolet... | Answered on Jan 31, 2015


Get a 12v tester and use it to find your hot wire usually the blue wire but it changes depending on where the truck was built.

2000 Chevrolet... | Answered on Jan 31, 2015


Is your security light flashing? If your Tahoe has the factory ant-theft system, if the security light is flashing while you are cranking your anti-theft system has been activated. It is common for the Tahoes to wear out the ignition lock assembly, lock cylinder and the ignition switch(electrical) which is attached to the lock assembly. I have replaced all three parts with great success and solved the no start problem on several GM trucks.

The most common problem with these vehicles is the fuel pump. The pump should run for a few seconds when you turn the key on before you crank the engine. If you don't hear the pump run, go to the fuse/relay box under the hood. Look at the diagram on the inside of the lid and locate the fuel pump fuse and relay. Check the fuse to see if it is blown put it back if OK or replace it. Unplug the fuel pump relay and use a paper clip to jumper across terminals #30 & #87 where the relay plugs in. If the fuel pump starts running, you should be able to hear it run at the back of the vehicle, where the tank is. If you don't hear the pump running, hit the center of the tank dead-center with a rubber or wooden mallet. If the pump still doesn't run, see if you can get to the wires going to the fuel pump and wiggle them. If you hear the pump run, try starting the engine. If it starts, replace the relay, if that was the problem or the fuel pump AND relay if the fuel pump was the problem. WARNING! WHEN YOU UNPLUG THE PAPER CLIP. IT MAY BE HOT!!!
The fuel pumps AND connector are big problems with GM trucks. If you replace the fuel pump(which is located in the fuel tank), use only the factory pump which you can buy at your GM dealer or an auto parts store that sells Delco parts. If the fuel pump used the small square four-pin electrical connector, replace it with the fuel pump. The latest GM/Delco fuel pumps will come with the new plug which you MUST change over as it is now a flat four-pin connector.
GOOD LUCK!

2000 Chevrolet... | Answered on Jan 05, 2015


it is the ground that goes to what you are towing

2000 Chevrolet... | Answered on Dec 27, 2014


Go on google or bing images, you might get a picture that helps. If not find your local garage or DIY neighbour to help. Do you mean the steel door strap? In which case you may have to access the inside of the door by removing the trim panel. But I would have thought it was all accessable from outside with a socket or 2.

2000 Chevrolet... | Answered on Dec 05, 2014


Usually this is caused by the exhaust, and most common is the heat shield around the catalytic converter. Sometimes these can be spot welded, by I have fixed a few by putting together a few large stainless hose clamps and placing all the way around the unit and tighten them up. Sometimes the rattle is internal, and replacement is the only option. If so, rather than getting a very expensive stock replacement, you can by a universal easy flow hot rod type for about $100, plus installation.

2000 Chevrolet... | Answered on Dec 01, 2014


There is one sensor and several solenoids. The temperature sensor is the only sensor. The rest are solenoids. To replace the temp sensor, you have to remove or replace the valve body, depending on your expertise.

2000 Chevrolet... | Answered on Nov 01, 2014


Pull out the bulb, it is probably black. You probably touched it with your finger when removing it or reinstalling it and it blew out, either that or the little tip on the bulb got broken off. Either way it will need to be replaced.

2000 Chevrolet... | Answered on Sep 23, 2014


Check that the heater core's two tubes that enter the firewall are getting hot. If they are, then you are having a blend door problem which will require disassembling the dashboard instruments to get at the vacuum motors that control the blend doors.

If the heater core is not getting hot at both tubes, then the following procedure outlines how to change the heater core out:

Removal & Installation






Heater core removal
gm-10-00-589.gif





To Remove:



  1. Remove the HVAC assembly.
  2. Remove the heater core cover screws.
  3. Remove the heater core cover from the HVAC assembly.
  4. Remove the heater core gasket from the core.
  5. Remove the heater core from the HVAC module assembly.


To Install:



  1. Install the heater core to the HVAC module assembly.
  2. Install the heater core cowl gasket to the HVAC module assembly.
  3. Install the heater core cover and screws to the HVAC module assembly.
  4. Install the HVAC module assembly to the vehicle.


prev.gif next.gif

2000 Chevrolet... | Answered on Sep 15, 2014


A lot of models have changed you might have to go with the same that is in it a 2001 might or a1999 as well take vin number and call salvage yards instead of dealers FYI

2000 Chevrolet... | Answered on Sep 02, 2014


Please go here on pc, for more info on this problem code. .obd-codes.com/p0446 Good-Day!

2000 Chevrolet... | Answered on Sep 01, 2014


axle bearing

2000 Chevrolet... | Answered on Jul 17, 2014


Go online and search for a service manual...there are many sites for this.

2000 Chevrolet... | Answered on Jul 17, 2014


if the security light stays on and is not blinking when the key is turned on , (but do not try to start the car). then you can do a key computor. communication .turn key on and off and[ on ]leave it on for exzactly 10 minutes.the security light will turn off, now take key back to off and now start the car.

2000 Chevrolet... | Answered on Jul 10, 2014


Are you serious???? This is your description for a problem that could have 10,000 different causes?

2000 Chevrolet... | Answered on Jul 01, 2014


more than likely that it is either ba crankshaft position sensor if it has one or ignition module because they build resistance when the copper windings inside them get hot on the crankshaft sensor or when the ignition module heats up they begin to fail its very common for these things to go bad on chevrolets also you might want to look into your fuel pressure because fuel pumps also begin to fail in this way you described when they are worn out and when they cool down they work again

2000 Chevrolet... | Answered on Jun 08, 2014


Check fuse, or wiring.

2000 Chevrolet... | Answered on Jun 01, 2014


Unlock the vehicle from door lock with key and retry also lock it and make sure security system is operating

2000 Chevrolet... | Answered on May 25, 2014

Not finding what you are looking for?
2000 Chevrolet Tahoe Logo

531 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85161 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Tahoe Chevrolet

  • Tahoe Chevrolet

Most Popular Question

2000 chevy tahoe when put in 2wheel rear

  • Cars & Trucks
Loading...