20 Most Recent
2000 Chevrolet Camaro - Page 8 Questions & Answers
Axle
You'll have to remove the rear diff. cover. Remove the tires and brake drums if equipped. There is an 8mm nut holding a rod in that is in the middle of the diff. After removing the set screw, the pin will want to slide out. Position the rear diff. in a way that you can see the axles clearly and still let the pin slide out. Once you remove the pin, you don't want to rotate the diff. Push the axles in to remove the "C" clips holding the axle in and slide the axle out. The "C" clip is located at the end of the inner part of the axles.
1996 Z28 camaro
sounds like transmission shift solenoid also make sure ur plugs and wires are good or u can get a similiar prob
1986 2.8l V6. What is the firing order?
This link might be help: https://www.google.com/search?q=1986+2.8l+V6+firing+order&source=lnms&tbm=isch&sa=X&ved=2ahUKEwjdmPm0mJTyAhVhILcAHSVjC9AQ_AUoAXoECAEQAw&biw=1366&bih=625
Can you show me what the starter for a 1982 Chevy Camero looks like?
this is for a stock 82 https://www.napaonline.com/en/p/NNE4N6273?cid=paidsearch_shopping_dcoe_google&campaign=GSC-Alternators-Starters&campaign_id=6503920054&adgroup_id=73349362010&adtype=pla&gclid=Cj0KCQjwl_SHBhCQARIsAFIFRVXyzIJiL6h3_pf0uJWjvclyMLp7j8i0EcHdDHOPmCwBg3LPEg3eAtEaApj5EALw_wcB&gclsrc=aw.ds& and located bottom back side of engine passenger side
2015 Chevy camero ac quit working, its not blowing cold air
Probably lost freon and now it won't cool. The system needs to be vacuum and pressure tested to find the leak and fix. It could be a seal on the compressor or a leak in a hose or condenser. You should see some oil leaking from the system where the leak is.
2015 Chevy camero
Freon is not at the proper amount so the high and low pressures are not right. Thus, you get warm air at idle and cool air at higher rps when driving.
2002 Camaro SS Z-28 quit running on the highway
Fuel pressure regulator may be vaccuum actuated on forward fuel rail... as this regulates fuel rail pressures, also see if fuel is making it into vacuum line if it is ... diaphragm popped, check this first. Before a fuel pump, which sounds where this is leading...
Pcm graund locatin camaro 3.8 2000
PULL THE WHITE OR CLEAR CONNECTOR AT THE PCM,,,CHECK THE WIRE AT PIN 18 (BLACK WIRE / WHITE STRIPE FOR GROUND.
The following is a summary of the instructions included with the service kit:
1. Remove the negative terminal from the battery.
2. Move the wire located at connector J3 (WHITE/GREY/CLEAR), pin 18 to connector J1 (BLUE), pin 23.
3. Install the jumper wire between connector J2 (RED), pin 26 and connector J3 (WHITE/GREY/CLEAR), pin 18.
4. Install the tag included in the kit around the VCM wiring harness. This tag notes that the wiring harness has been modified.
5. Reconnect the negative battery terminal.
Road test to verify that the condition has been corrected. If any of the following conditions are noted, the transmission should be repaired or replaced using the most cost effective method. Canadian dealers should repair the transmission.
1.
Transmission fluid oxidation or excessive sediment.
2. Transmission slip or flare after this service fix is performed.
3. DTC P1870 is stored on a 4L60-E (M30).
The following tools are available from Kent-Moore (1-800-345-2233) for use in removing and relocating the VCM wires:
1. J 41758 Terminal Tool; used to remove the wire from the VCM connector.
2. J 41759 Punch; used to punch a new hole through the connector seal
Not finding what you are looking for?