20 Most Recent 1988 Buick LeSabre Questions & Answers


You can check this website. You find there fuse box diagram and description for Buick LeSabre

LeSabre CARKNOWLEDGE

1988 Buick... | Answered on Oct 25, 2018


Yes an OBD 1 meter will give you a better idea as to what the problem is,however it would be more cost effective to find an OBD 2 meter with the capability to test OBD 1 cars.I do have the same problem with my 88 Lasabre,the 3 codes coming up would be the cam shaft sensor($20),the ignition mudule ($140),or the ECM ($80),I found that on mine the number 3 cylinder does not look like it is firing when I inspect the spark plug,but the only code I get # 41.I'am going to start with the cheapest part first.If you have a basic understanding of the mechanics of vehicles(or a haynes repair manual) you could probably replace this yourself.If you already found the solution to this problem please email me at mikehitchner@comcast.net so that I can fix mine.Thanks

1988 Buick... | Answered on Mar 23, 2016


Buick cars don't have them. From the fuel pump relay under the hood, the pump's power wire goes directly to the gas tank and the fuel pump connector.

If your pump is not turning on, check for power on the gray wire at the gas tank electrical connector while someone cranks the engine over. The pump wire, I think it is gray, should have battery voltage when the engine is cranking. If it does, you probably need a new fuel pump. Dropping the gas tank is no fun, it is a dirty job, not real difficult, just not a fun relaxing afternoon.

1988 Buick... | Answered on Aug 15, 2015


change the fuel pump relay.

1988 Buick... | Answered on Dec 27, 2013


Trick question There are no 4wd

1988 Buick... | Answered on Oct 02, 2013


You may need a shop manual to get the testing procedures. You need to know if the ignition module is getting power and a signal from the cam and crank sensors.

1988 Buick... | Answered on Sep 26, 2013


go to ebay ,buick spares

1988 Buick... | Answered on Sep 19, 2013


There are 3 bolts inside that have backed out, this is a tough job. You have to have special tools to complete this job. You have to pull the pins on the side after disassembling to access the bolts.

1988 Buick... | Answered on Apr 09, 2013


they are a heat sheild they should bolt on with the exaust

1988 Buick... | Answered on Dec 09, 2012


Check the condition and operation of the idle control valve.

1988 Buick... | Answered on Nov 15, 2012


Its a faulty idle air control valve.You can take it off and clean it using a non-chlronated brake cleaner and a wire brush or and a scraperor you can replace it with a new one just make sure to reset the computer afterwards by disconnecting the ground cable on the battery for 30 seconds then start it.

1988 Buick... | Answered on Oct 21, 2012

Not finding what you are looking for?
Cars & Trucks Logo

217 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

2000 Buick LeSabre
2000 Buick LeSabre

1,704 Questions

1997 Buick LeSabre
1997 Buick LeSabre

1,572 Questions

1995 Buick LeSabre
1995 Buick LeSabre

1,066 Questions

1994 Buick LeSabre
1994 Buick LeSabre

891 Questions

1998 Buick LeSabre
1998 Buick LeSabre

882 Questions

Top Buick Experts

Marvin
Marvin

Level 3 Expert

85111 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

LeSabre Buick

  • LeSabre Buick

Most Popular Question

1988 buick lesabre limited edition used

  • Cars & Trucks
Loading...